background image

Specifications

 

Electrical Supply Requirements 

 

Electrical Connection 

GP8910GE / GEC 

Electrical supply connection point is located at the rear of the appliance, approximately 80 mm from 
the right hand side and 466 mm from the rear and 150 mm from the floor. 

 

GP8121GE / GEC 

Electrical supply connection point is located at the rear of the appliance, approximately 380 mm from 

the right hand side and 466 mm from the rear and 150 mm from the floor. 

 

When connecting a this electric appliance to the mains supply, ensure that the following is carried 

out:- 

• 

An isolating switch is fitted within 2 m of the appliance, but not on the appliance and in 
such a position that the user does not have to reach across the cooking surface. 

• 

Supply cord shall be oil-resistant, sheathed flexible cable and not lighter than ordinary 
polychloroprene or other equivalent synthetic elastomer sheathed cord (as per AS / NZS  

3191 part 2.10.11. or IEC 60245-IEC-57) e.g. HO5 RN-F Type. 

• 

The branch supply line shall be individually overload protected to the correct current rating 
and the supply chord shall be protected against any mechanical or thermal damage. 

• 

A grommet is fitted around the wiring entry hole into the appliance. 

• 

All wiring connections must be tight. 

 

Refer to the appropriate wiring standards for the size of cable that is to be supplied to an appliance 

for the current drawn on that line. 

WARNING: 

 

T

HIS

 

APPLIANCE

 

MUST

 

BE

 

EARTHED

.  I

F

 

THE

 

SUPPLY

 

CORD

 

IS

 

DAMAGED

IT

 

MUST

 

BE

 

REPLACED

 

BY

 

A

 

SUITABLY

 

QUALIFIED

 

PERSON

 

IN

 

ORDER

 

TO

 

AVOID

 

A

 

HAZARD

MODEL 

1-Phase Connection 

1P+N+E 

230-240V 

3-Phase Connection 

3P+N+E 

400-415V 

GP8910GE 
GP8121GE 

6.5 kW,  

26.6 Amps @ 235V 

6.5 kW 

L1 - 8.2 Amps 

L2 - 9.2 Amps 

L3 - 9.2 Amps 

GP8910GEC 
GP8121GEC 

6.8 kW, 

27.9 Amps @ 235V 

6.8 kW 

L1 - 9.5 Amps 

L2 - 9.2 Amps 

L3 - 9.2 Amps 

Summary of Contents for GP8910GE

































Reviews: