REAR OVER FENDER
2018/07
ATTACHED
TAPPING SCREWS
(M4 x 14)
CROSS SECTION
OF THE DOOR
CROSS SECTION
OF PART B
CROSS SECTION
OF PART C
BODY SIDE
Bottom of
WALD Rear
Over Fender
must upper
than the
Bottom of Door
PART A
PART B
PART B
PART C
PART A
Install Parallelly
with the Body Side
ATTACHED
TAPPING SCREWS
(M4 x 14)
GDJ150W/TRJ150W
PARTS
QUANTITIES
REAR OVER FENDER
1 SET
1
2
REAR OVER FENDER
RUBBER MOULDING (Black/Gray)
TAPPING SCREWS (M4 x 16)
(2017y-)
LAND CRUISER
PRADO
INSTALLATION MANUAL
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD OVER FENDER FOR TOYOTA LAND CRUISER PRADO.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION.
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
Use caulking glue
to fill the gap
between the product
and the body.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
ATTENTION
【
BEFORE PAINTING
】
※ The picture shows for Left Side, and install on the Right Side as same as for Left Side.
１） Temporarily fix the attached WALD Rear Over Fender according to the PICTURE 1, 2, 3 and 4.
(In Order to Part A→B→C)
２） Put Part A of WALD Rear Over Fender on the body according to Picture 3.
※ Adjust the details of WALD Rear Over Fenders to fit the body by rasps or sandpapers.
３） Use the attached screws to install Mark the installation position,
then mark the holes for the attached tapping screws.
４） Take off the Part A from the body, and make holes according to the marked positions.
５） Use the masking tape to mark the location of WALD Rear Over Fenders on the body.
６） Paint WALD Rear Over Fenders according to the picture (As per enclosure).
【AFTER PAINTING】
７） Completely degrease the installation positions,
then fix the attached rubber mouldings on WALD Rear Over Fenders.
８） Completely degrease the installation positions,
then use caulking glue to install WALD Rear Over Fenders to the body.
９） Check all the details of the fitment, then tighten the OEM Tapping Screws..
１０） Leave it till completely fixed.
ATTACHED
RUBBER MOULDING
PARTIAL CROSS
SECTION OF PART C
※ MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ REMOVE THE BATTERY BEFORE ALL THE WIRING WORKS.
※ ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY.
ATTENTION
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
WALD. INTERNATIONAL
ZIP: 569-0072
TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
OEM
TAPPING
SCREWS
AROUND FUEL PANEL
(Only on Left Side)
ATTACHED DOUBLE SIDED TAPE
4〜5mm
4〜5mm
5mm
6mm
※All the widths are only for a reference.
※Type of Adhesive : Use the Silicone Glue
PICTURE 1
PICTURE 4
PICTURE 2
PICTURE 3
（2）At Regular
Interval
（1）According to OEM Fender Arch Line
335mm
150mm
BETWEEN DOOR AND
REAR OEM FENDER
RUBBER MOULDING
Adhesion Surface to
WALD Over Fender
■HOW TO ATTACH THE RUBBER MOULDING (STEP 6)
Apply primer on the adhesion
surface of
WALD Over Fender
before attaching
the rubber mouldings.
BODY PRESS LINE
TOP OF
WALD
REAR SKIRT
OEM
TAPPING
SCREWS
