2018/07
FRONT SPOILER
GDJ150W/TRJ150W
PARTS
QUANTITIES
FRONT SPOILER
1
4
2
2
1
1 SET
1
FRONT SPOILER
TAPPING SCREWS (M5 x 15)
BRACKET A WITH NUTS
BRACKET B
CHROME ACCENT FOR CENTER
CHROME ACCENT FOR RIGHT AND LEFT
RUBBER MOULDING (Black/Gray)
(2017y-)
LAND CRUISER
PRADO
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
WALD. INTERNATIONAL
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
INSTALLATION MANUAL
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD FRONT SPOILER FOR TOYOTA LAND CRUISER PRADO.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION.
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
Use caulking glue
to fill the gap
between the product
and the body.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
ATTENTION
【BEFORE PAINTING】
１） Temporarily install WALD Front Spoiler to the body with the attached brackets A and B.
(Do not use the double sided tape at this moment)
※ Adjust the details of WALD Front Spoiler to fit the body by rasps or sandpapers.
２） Check the balance of the installation position of WALD Front Spoiler on OEM Front Bumper.
３） Paint WALD Front Spoiler according to the picture (As per enclosure).
【AFTER PAINTING】
４） Attach the rubber moulding on WALD Front Spoiler.
５） Completely degrease the installation position.
６） Use caulking glue and the double sided tape to install WALD Front Half Spoiler
with the attached brackets to OEM front bumper, then fix all the attached tapping screws tightly.
※ The ends of the release paper of the double sided tape must be fold to adjust the location.
７） Completely degrease the installation position for the attached Chrome Accents.
８） Use caulking glue and the double sided tape to fix the chrome accents on WALD Front Spoiler.
９） Leave it till completely fixed.
※ MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY.
ATTENTION
PICTURE 1
HOW TO INSTALL BRACKET (STEP 2, 9)
TAPPING SCREWS (M5 x 15)
ATTACHED
BRACKET A
ATTACHED
BRACKET B
CHROME ACCENT FOR RIGHT AND LEFT
CHROME ACCENT
FOR CENTER
ATTACHED DOUBLE SIDED TAPE
DOUBLE SIDED TAPE
(Sold Separately)
DOUBLE SIDED TAPE
(Sold Separately)
RUBBER MOULDING
Adhesion Surface to
WALD Front Spoiler
■HOW TO ATTACH THE RUBBER MOULDING (STEP 5)
Apply primer on the adhesion
surface of
WALD Front Spoiler
before attaching
the rubber mouldings.
ATTACHED BRACKET A
FIXED NUT
LONG HOLE
TAPPING SCREWS
(M5 x 15)
OEM
CLIP
OEM
BOLT
TAPPING SCREWS
(M5 x 15)
ATTACHED
RUBBER MOULDING
※Type of Adhesive : Use the Silicone Glue
※All the widths are only for a reference.
PICTURE 2
LOCATION OF
WALD FRONT SPOILER
Straight Line from the borderline
between OEM front bumper and
fender to WALD Front Spoiler.
About 313 mm
