background image

WARRANTY

2 - YEAR LIMITED WARRANTY

WAHUDA warrants its machinery to be free of defects in workmanship and materials for a period of two
(2) years from the date of the original purchase by the original owner. This warranty applies to products
sold  in  United  States  only.  The  warranty  does  not  apply  to  any  product  used  for  professional  or
commercial production purposes nor for industrial or educational applications. Such cases are covered
by our 1 year Limited Warranty with the Conditions and Exceptions.

Warranty  does  not  include  failures,  breakage  or  defects  deemed  after  inspection  by  an  Authorized
Service  Center  or  our  agent  to  have  been  directly  or  indirectly  caused  by  or  resulting  from  improper
use, lack of or improper maintenance, misuse or abuse, negligence, accidents, damage in handling or
transport,  or  normal  wear  and  tear  of  any  part  or  component.  Examples  are  consumables  such  as
inserts and knives or wear items like drive belts, bearings or brushes. Additionally, warranty is void if
repairs  or  alterations  are  made  to  the  machine  by  an  unauthorized  service  center  without  the  direct
consent of WAHUDA. 

To  file  a  claim  of  warranty,  call  toll  free  877-568-8879  or  email  [email protected]  .
Warranty applies to the original buyer only and cannot be transferred. Your machines date of purchase
and serial number have already been registered with WAHUDA when shipped. If you purchased your
machine from one of our authorized dealers, please go online at www.wahudatools.com and register
your machine online. Thus, you will only need to provide your full name when contacting WAHUDA.

The  defective  units  should  be  returned  Freight  prepaid  to  WAHUDA’s  Authorized  Service  Center  for
inspection. If the warranty claim is considered to be invalid due to exclusions listed above, WAHUDA
will  at  your  direction  dispose  of  or  return  the  product.  In  the  event  you  choose  to  have  the  product
returned you will be responsible for the handling and shipping cost of the return. 

WAHUDA furnishes the above warranties in lieu of all other warranties, express or implied. WAHUDA
shall  not  be  liable  for  any  special,  indirect,  incidental,  punitive  or  consequential  damages,  including
without limitation to loss of profits arising from or related to the warranty, the breach of any agreement
or warranty, or the operation or use of its machinery, including without limitation damages arising from
damage  to  fixtures,  tools,  equipment,  parts  or  materials,  direct  or  indirect  loss  caused  by  any  other
part, loss of revenue or profits, financing or interest charges, and claims by and third person, whether
or not notice of such possible damages has been given to WAHUDA. Not Responsible for damages of
any  kind  for  any  delay  by  or  failure  of  WAHUDA  to  perform  its  obligations  under  this  agreement  or
claims  made  a  subject  of  a  legal  proceeding  against  WAHUDA  more  than  one  (1)  year  after  such
cause of action first arose.

The validity, construction and performance of this Warranty and any sale of machinery by WAHUDA
shall be governed by the law of the State of Tennessee, without regard to conflicts of law’s provisions
of any jurisdiction. Any action related in any way to any alleged or actual offer, acceptance or sale by
WAHUDA  or  any  claim  related  to  the  performance  of  and  agreement  including  without  limitation  this
Warranty, shall take place in the federal or state courts in Shelby County, Tennessee. 

WAHUDA reserves the right to change the specifications of its machines without prior notice. 

3

Summary of Contents for 60200PC-WHD








































Reviews: