background image

 

805.241.009 

Date: October 14, 2016

 

Technical specifications: 

 

Item No. 

 

 

: 241 

Dimensions  

 

: 240 x 210 x 150 mm. / 9.5 x 8.3 x 5.19 in. (L-W-H)  

  (Without mounting clamp) 

Power supply 

 

: 230 V AC 50 Hz (optional 120V/60Hz). 

Power consumption  

: Max 200 Watt. 

Power plug  

 

: Neutrik powerCON male 

DMX Control signal 

: DMX 512 1990 + DMX512A / 7 channels used. 

DMX connection  

: 5 pole XLR, In & link 

Lifting height 

 

: 10 m. (33 ft.)  

Lifting capacity   

: 10 kg. (22 lbs.) 

Lifting speed  

 

: Variable, 5-30 cm/sec. (2-11.8 inch/sec.) 

Lifting wire 

 

: 2 mm galvanized steel wire, 8mm snap hook. 

 

 

 

 

  Calculated breaking strength: 240 kg 

Min. Load   

 

: 0.4 kg (0.88 lb) 

Noise emission

   

: ~55 dB

  

Weight 

 

 

: 5.2 kg (11.5 lbs.)  

Mounting clamp   

: Slim eye coupler (Max load: 300 kg) 50 mm (2 inch.) 

Motor 

 

 

: 24 V DC, 28.9 W, IP30 

Wire lifetime 

 

: At 2.5kg the wire will last up to 80,000 cycles running up and down. 
  At 5kg the wire will last up to 20,000 cycles running up and down.  
  At 10kg the wire will last up to 15,000 cycles running up and down. 

Summary of Contents for Winch 10




















Reviews: