background image

 

 

Important Comments 

  

  7 

 

 

Safety Notes 

 

WAGO-I/O-SYSTEM 751 
AS-Interface Components IP67 

1.4 Safety Notes 

 

Attention

 

Switch off the system prior to working on bus modules! 

In the event of deformed contacts, the module in question is to be replaced, as 
its functionality can no longer be ensured on a long-term basis. 

The components are not resistant against materials having seeping and 
insulating properties. Belonging to this group of materials is: e.g. aerosols, 
silicones, triglycerides (found in some hand creams).  
If it cannot be ruled out that these materials appear in the component 
environment, then additional measures are to be taken:  
- handling of the components only with clean tools and materials. 

 

Attention

 

Cleaning of soiled contacts may only be done with ethyl alcohol and leather 
cloths. Thereby, the ESD information is to be regarded. 

Do not use any contact spray. The spray may impair the functioning of the 
contact area.  

 

Attention 

Unused connection sockets must be sealed with filler plugs in order to keep 
IP67 degree of protection! 

 

1.5 Scope 

This manual describes the Digital Input Module 751-4001 
AS-Interface Module 4OUT 24V/2A Single of the m
odular WAGO-I/O-
SYSTEM 751. 

Handling, assembly and start-up are described in the manual of the Fieldbus 
Coupler. Therefore this documentation is valid only in the connection with the 
appropriate manual.

Summary of Contents for I/O-SYSTEM 751-4001



















Reviews: