background image

12  Important Notes 

WAGO I/O System 750 

 

 

750-506 2DO 24V DC 0.5A/ diagnostics 

Manual 

 

Version 1.2.1  

 

Public 

Pos: 17.11 /Alle Serien (Allgemeine M odul e)/Überschriften/Ebene 2/Sicherheitshinweise - Ü berschrift 2 @ 6\mod_1260180299987_21.docx @  46724 @ 2 @  1 

 

2.2 

Safety Advice (Precautions) 

Pos: 17.12 /Alle Serien (Allgemeine M odul e)/Sicherheits- und sonstige Hinweise/Ei nlei tung Sicherheitshinweise Har dwar e @ 6\mod_1260180170493_21.docx @ 46720 @  @ 1 

 

For installing and operating purposes of the relevant device to your system the 

following safety precautions shall be observed: 

Pos: 17.13.1 /Alle Serien (Allgemeine M odul e)/Sicherheits- und sonstige Hinweise/Gefahr/Gefahr: Nicht an Geräten unter Spannung ar bei ten! @ 6\mod_1260180365327_21.docx  @  46727 @   @ 1 

 

 

 

 

Do not work on devices while energized! 

All power sources to the device shall be switched off prior to performing any 

installation, repair or maintenance work. 

 

Pos: 17.13.2 /Alle Serien (Allgemeine M odul e)/Sicherheits- und sonstige Hinweise/Gefahr/Gefahr: Pr odukt nur i n einem geeigneten Gehäuse ei nbauen! @ 33\mod_1543581881435_21.docx @ 511972 @  @ 1 

 

 

 

 

Install device in only one suitable enclosure! 

The device is an open system. Install the device in a suitable enclosure. This 

enclosure must: 

•  Guarantee that the max. permissible degree of pollution is not exceeded. 

•  Offer adequate protection against contact. 

•  Prevent fire from spreading outside of the enclosure. 

•  Offer adequate protection against UV irradiation. 

•  Guarantee mechanical stability 

• 

Restrict access to authorized personnel and may only be opened with tools 

 

Pos: 17.13.3 /Alle Serien (Allgemeine M odul e)/Sicherheits- und sonstige Hinweise/Gefahr/Gefahr: Trennvorrichtung und Ü berstromschutz @ 33\mod_1543915978439_21.docx @ 512267 @  @ 1 

 

 

 

 

Ensure disconnect and overcurrent protection! 

The device is intended for installation in automation technology systems. 

Disconnect protection is not integrated. Connected systems must be protected by 

a fuse. 

Provide suitable disconnect and overcurrent protection on the system side! 

 

Pos: 17.13.4 /Alle Serien (Allgemeine M odul e)/Sicherheits- und sonstige Hinweise/Gefahr/Gefahr: Unfall verhütungsvorschriften beachten! @ 6\mod_1260180657000_21.docx @  46735 @  @ 1 

 

 

 

Pos: 17.13.5 /Alle Serien (Allgemeine M odul e)/Sicherheits- und sonstige Hinweise/Gefahr/Gefahr: Auf nor mgerechten Anschl uss achten! @ 6\mod_1260180753479_21.docx @ 46739  @   @  1 

 

 

 

 

Ensure a standard connection! 

To minimize any hazardous situations resulting in personal injury or to avoid 

failures in your system, the data and power supply lines shall be installed 

according to standards, with careful attention given to ensuring the correct 

terminal assignment. Always adhere to the EMC directives applicable to your 

application. 

 

Pos: 17.14.1 /Serie 750 ( WAGO I/O SYST EM)/Anschließ en/Ei nspeisekonzepte/Achtung: Systemversorgung nur  mi t geeigneter Absicher ung! - UL 61010 - @ 32\mod_1535966317803_21.docx @ 498058 @  @ 1 

 

Summary of Contents for 750-506 Series























































Reviews: