background image

15

W 690 Flexio Extra Spray Kit

AUS

manufacturer and have been mounted to the device and are operated properly. If third-

party accessories or spare parts are used, the manufacturer is exonerated wholly or partly 

from his/her liability if use of the third-party accessories or spare parts have caused a 

defect in the product.

23. Correction of Malfunctions

Malfunction

Cause

Remedy

No coating 

material emerges 

from the nozzle

• 

Nozzle clogged

• 

Material quantity too small 

• 

No pressure build-up in container

• 

Container empty

• 

Feed tube clogged

• 

Ventilating bore (Fig.17, A) clogged

 

Clean

 

Increase the quantity 

of material

 

Tighten container

 

Refill

 

Clean

 

Clean

Coating material 

drips from the 

nozzle

• 

Coating material assembly at air 

cap, nozzle or needle

• 

Nozzle loose

• 

Nozzle seal worn

• 

Nozzle worn

 

Clean  

 

Union nut tighten

 

Change

 

Change

Atomisation too 

coarse

• 

Material volume too large 

• 

Nozzle contaminated

• 

Air cap assembled incorrectly 

• 

Viscosity of coating material too 

high 

• 

Too little pressure build-up in 

container

• 

Air filter heavily soiled

• 

Amount of air too low

 

Reduce the material 

volume

 

Clean

 

Snap air cap properly 

into place (fig. 23, 1)

 

Dilute further 

 

Tighten container 

 

Change

 

Turn the air volume 

control to the left (+)

Spray jet pulsates

• 

Coating material in container 

running out

• 

Nozzle seal worn

• 

Air filter heavily soiled

 

Refill 

 

Replace

 

Change

Coating material 

causes "paint 

tears"

• 

Too much coating material applied.

 

Reduce the material 

volume

Summary of Contents for W 690 Flexio



























Reviews: