28
Control Pro 250 M / 275 M
DE
EN
Correction of Malfunctions
Problem
Cause
Remedy
The sprayer does
not start.
•
The sprayer is not plugged in.
•
The sprayer was turned off while still under
pressure.
•
No voltage is coming from the wall plug.
•
The extension cord is damaged or has too low
a capacity.
•
Device overheated
•
There is a problem with the motor.
•
Plug the sprayer in.
•
Perform pressure relief procedure and set selector
switch back to SPRAY
•
Properly test the power supply voltage.
•
Replace the extension cord.
•
Switch the device off, turn the selector switch to the
PRIME position (vertical), remove the mains plug
and allow device to cool down for min. 30 minutes.
Eliminate the cause of overheating, e.g. covered
ventilation slot.
•
Please contact Wagner Service
The spray device
runs but does not
suck up any paint
when the selector
switch is set to the
PRIME position.
•
The unit will not prime properly or has lost
prime.
•
The paint bucket is empty or the suction tube
is not totally immersed in the paint.
•
The suction tube is clogged.
•
The inlet filter is clogged.
•
The suction tube is loose at the inlet valve.
•
The inlet valve or outlet valve is stuck.
•
The inlet valve is worn or damaged.
•
The PRIME/SPRAY valve is plugged
•
Try to prime the unit again.
•
Refill the bucket or immerse the suction tube in paint.
•
Clean the suction tube.
•
Clean the inlet filter.
•
Tighten it securely.
•
Follow the instructions in the chapter "Help with
suction problems".
•
Replace
•
Please contact Wagner Service
The sprayer draws
up paint but the
pressure drops
when the gun is
triggered.
•
The spray nozzle is worn.
•
The inlet filter is clogged.
•
The spray nozzle is blocked (if fitted)
•
The paint is too viscous or contaminated.
•
The inlet valve is worn or damaged.
•
Replace the spray nozzle with a new nozzle.
•
Clean the inlet filter.
•
Clean or replace the filter.
•
Thin or strain the paint.
•
Replace
The spray gun leaks
•
Internal parts of the gun are worn or dirty.
•
Please contact Wagner Service
The nozzle
assembly leaks
•
The nozzle was assembled incorrectly.
•
A seal is dirty.
•
Check the tip assembly and assemble properly
•
Clean the seal.
The spray gun will
not spray.
•
The spray nozzle is plugged.
•
The spray nozzle is blocked (if fitted)
•
The spray tip is in the reverse position.
•
Clean the spray nozzle and use the HEA filter set.
•
Clean or replace the filter.
•
Put the nozzle in the forward position.
The paint pattern is
tailing.
•
The paint is too viscous or contaminated.
•
The spray nozzle is plugged.
•
The spray nozzle is worn.
•
The spray nozzle is blocked (if fitted)
•
The inlet filter is clogged.
•
The inlet valve is worn or damaged.
•
Thin or strain the paint.
•
Clean the spray nozzle and use the HEA filter set.
•
Replace the spray nozzle with a new nozzle.
•
Clean or replace the filter.
•
Clean the inlet filter.
•
Replace
CE Declaration of Conformity
We declare under sole responsibility that this product conforms to the following relevant stipulations:
2006/42/EC, 2014/30/EU, 2011/65/EU, 2012/19/EU
Applied harmonised norms:
EN ISO 12100, EN 1953, EN 62841-1, EN 55014-1, EN 55014-2, EN IEC 61000-3-2, EN 61000-3-3, EN 62233
The EU declaration of conformity is enclosed with the product.
If required, it can be re-ordered using order number
2373934
.
