background image

© 1995 Wagner Spray Tech

5

All rights reserved.

NOTE: Do not use more than 100 feet of extension

cord.  If you need to paint further than 100
feet from your power source, use more paint
hose, not more extension cord.  Shorter
extension cords will ensure maximum electri-
cal power for proper operation.

GROUNDING INSTRUCTIONS

This product must be grounded. In the event of an
electrical short circuit, grounding reduces the  risk of
electric shock by providing an escape wire for the electric
current. This product is equipped with a cord having a
grounding wire with an appropriate grounding plug. The
plug must be plugged into an outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.

WARNING

Improper installation of the grounding plug can result
in a risk of electric shock.

If repair or replacement of the cord or plug is necessary,
do not connect the green grounding wire to either flat
blade terminal. The wire with insulation having a green
outer surface with or without yellow stripes is the ground-
ing wire and must be connected to the grounding pin.

Check with a qualified electrician or serviceman if the
grounding instructions are not completely understood, or
if you are in doubt as to whether the product  is properly
grounded.  Do not modify the plug provided.  If the plug
will not fit the outlet, have the proper outlet installed by a
qualified electrician.

This product is for use on a nominal 120 volt circuit and
has a grounding plug that looks like the plug illustrated
below. A temporary adapter which looks like the adapter
illustrated in the figure below may be used to connect this
plug to a 2 pole receptacle as shown if a properly
grounded outlet is not available. The  temporary  adapter
should be used only until a properly grounded outlet as
shown below can be installed by a qualified electrician.
The green colored rigid  ear lug or the grounding wire
extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet
box cover. Whenever the adapter is used, it must be held
in place by a metal screw.

Grounded Outlet

Grounding Pin 

Tab for Grounding Screw 

Adapter

Metal Screw

Cover fo grounded outlet box 

Summary of Contents for 0278712C





















Reviews: