background image

WAFER GSM-KEY REMOTE CONTROL UNIT 

http://www.waferstar.com 

Acknowledge

: ALARM_IN1=ON:SMS:300, ALARM_IN2=ON:PHONE:10 

If at phone mode: when receive the alarm input,then will phone the number in the alarm phone list until you 

reject the phone call or that will continue to phone the number again after the minutes setted. 

If at SMS mode: When receive the alarm input,then will send the SMS to the number in the alarm phone list 

until you send the SMS to PAUSE the alarm . 

 

(5) Config the SMS TEXT :   

(PC)

 

#PWD123456#UDI1:XXXXXX, UDI2:XXXXXX 

Acknowledge

: UDI1:XXXXXX, DI2:XXXXXX OKAY

 

(When the Alarm input is triggered,then will send the   
SMS you already setted with this UDI command) 

Check the text    set 

#PWD123456#UDI?

 

Acknowledge:

   

UDI1:ABC1, UDI2:ABC2 

 
#REPORT 
Report the system status change

   

(PC$PHONE)

 

When setup to: 

#PWD123456#REPORT=ON    

Then any device status change would send the alarm SMS to Alarm01 number

 

#PWD123456#REPORT=OFF 

No report for the device status change 

#PWD123456#REPORT? 
Check the REPORT setting status 
 
#CSQ 
Check GSM signal quality

.  

(PC$PHONE)

 

This command is useful to see what is the GSM network 
signal level your GSM-KEY is receiving. It ranges from 0 to 32 (if it is 0 we doubt it will 
ever answer...). You should have a signal above 12 to be sure of being able to open the 
gate in any condition. Better if above 16. You should add an external antenna if this is not the case, 
or eventually even change operator with another that serves your area better. 

#PWD123456#CSQ? 

Acknowledge:

 

CSQ IS 26 

 

#MODE Relay Operation Mode SETUP   

(PC$PHONE) 

#PWD123456#MODE0 

Acknowledge

:    RELAY SET TO MODE0 

#PWD123456#MODE1 

Acknowledge

:    RELAY SET TO MODE1 

If set to MODE0,that is 

Momentary pulse and If Config to MODE1,that is Ratchet relay 

#STATUS Check the config information of the terminal   

(PC$PHONE) 

#PWD123456#STATUS? 
You will receive a Acknowledge with: 
ALARM1=ON:SMS:040960,ALARM2=OFF:SMS:4352,GOT=05S,WHL=01,ALARM1=HIGH,
ALARM2=HIGH,BCPW=00,CSQ=10,RELAY1=ON,RELAY2=OFF 

Summary of Contents for GSM-KEY-3G

















Reviews: