Wacker Neuson RD 12A Repair Manual Download Page 114

Page: 114 / 138

Disassembly & Assembly

RD 12/RD 12A

wc_tx000671gb.fm

114

9.32 Installing the Hydraulic Tank

Prerequisites

Engine cool

Procedure

Follow the procedure below to install the hydraulic tank.

1. Place a plastic sheet and a container under the machine to collect any liquid which

drains off. Dispose of this liquid in accordance with environmental protection legislation.

2. Connect the hydraulic hoses to the hydraulic tank and position the hydraulic tank into

the frame. Tighten the fittings if loosened during the removal procedure.

3. Install the mounting bracket

(b)

4. Install the screws

(c)

that secure the hydraulic tank to the frame.

This procedure continues on the next page.

wc_gr004206

wc_gr004207

Summary of Contents for RD 12A











































































































































Search results

Summary of Contents for RD 12A

Reviews:

Related manuals for RD 12A

Brands by name

Popular brands

Wacker Neuson RD 12A, Repair Manual

Search results

Summary of Contents for RD 12A

Reviews:

Related manuals for RD 12A

Brands by name

Popular brands