background image

RD 12 / RD 12A

Vibration System and Steering

wc_tx000668gb.fm

59

Continued from the previous page.

5. Turn on the vibration and measure the relief and operating pressures. The relief 

pressure is the pressure registered on the gauge as soon as the vibration is 

turned on. The system will then settle into operating pressure. Record these two 

pressures.

6. Shut down the machine.

Compare the results from operating pressure, pump relief pressure, and exciter 
speed with the chart below. 

N = Normal, L = Low, H = High

If the exciter is binding or causing high operating pressures, perform the following:

1. Disconnect and remove the exciter motor 

(c)

 from the housing.

2. Turn the motor shaft and exciter shaft by hand and check that they both turn 

freely.

3. If either component does not turn freely, it has failed; replace it.

The vibration system has now been checked for poor vibration.

Operating

Pressure

Pump Relief

Pressure

Exciter 

Speed

Probable Cause

N

N

N

System OK

H

N

N or L

Exciter bearings or motor binding

N or L

N

L

Exciter motor worn

L

L

L

Exciter pump damaged or worn, relief 

valve defective, or needs adjusting

wc_gr004143

c

Summary of Contents for RD 12A











































































































































Reviews: