Wacker Neuson BTS 1030-8339 Repair Manual Download | Manualshive

Page: 20 / 44

background image

Carburetor

BTS Repair

wc_tx000301gb.fm

18

6.

Carburetor

6.1

Setting the carburetor

See Graphic: wc_gr001398

Set Idling Nozzle “L” at 1 3/8 (-1/16) turn

For the basic setting, turn in the idling nozzle “L” carefully as far as it
will go. Then back off “L” nozzle 1 3/8 turn.

For fine tuning, the “L” nozzle only needs to be changed by max.
- 1/16 of a turn.

“S” Idling Screw

When during idling the engine speed is too high (moving of cutting
disc) or too low (engine stalls), correct the the setting of idling screw
“S” (speed) accordingly.

“H” Main Nozzle

BTS 930/935: The main nozzle “H” is set at the factory to 6/8 of a turn.

BTS 1030/1035: The main nozzle “H” is set at the factory to 7/8 of a
turn except for machines built in 2002 (S/Ns 5289575 to 5355979)
which were set at the factory to 6/8 of a turn.

S

H

L

wc_gr001398

«
...
18
19
20
21
22
...
»

Summary of Contents for BTS 1030-8339













































Reviews:

No comments

Related manuals for BTS 1030-8339

CS-3000 TYPE 1E

Brand: Echo Pages: 8

Brand: Echo Pages: 36

DCT758-3 - DCT Cordless Phone

Brand: Uniden Pages: 84

Brand: Uniden Pages: 8

Brand: Milwaukee Pages: 9

Brand: MasterCraft Pages: 30

Brand: Omcan Pages: 20

Brand: Ryobi Pages: 42

Gigaset CX590 ISDN

Brand: Gigaset Pages: 84

Brand: VTech Pages: 21

Brand: VTech Pages: 19

Brand: VTech Pages: 2

Brand: VTech Pages: 1

Brand: VTech Pages: 31

Brand: VTech Pages: 1

Brand: VTech Pages: 46

LS5105 - Cordless Extension Handset

Brand: VTech Pages: 27

VONAGE IP8100 Series

Brand: VTech Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands