Wacker Neuson BTS 1030-8339 Repair Manual Download Page 31

Page: 31 / 44

BTS Repair

Crankcase / Crankshaft

wc_tx000306gb.fm

11. Crankcase / Crankshaft

11.1 Crankcase / crankshaft

See Graphic: wc_gr001410 and wc_gr001411

Complete crankcase

The complete crankcase is divided into the crankcase magnet side (2)
“MS”, and the crankcase clutch side (1) “KS”.

Removing the crankcase “MS”

To dismantle the magnet side (MS), unscrew the 4 fixing screws (3)
and the left lower screw (4).

Dismantling the crankcase

After removing the 5 fixing screws, separate the crankcase carefully by
tapping with a plastic hammer (a).

Replacing the crankshaft / bearing

First push bearing onto the crankshaft, then insert crankshaft with
bearing (5) into the case, “KS”. Place gasket on centering pins.

Note: To dismantle or assemble the bearings, heat the crankcase to
212–248°F (100–120°C).

Mounting the bearing / crankcase

Heat the crankcase “MS” and fit bearing into the case (b).

Note: The bearing faces with its open side to the crankshaft. Before
installation moisten the outside of the bearing with “Loctite 601”.

Mounting the crankcase

Tighten the 5 fixing screws with a torque of 7 ft.lbs. (10 Nm) (c).

wc_gr001410

wc_gr001411

Summary of Contents for BTS 1030-8339













































Search results

Summary of Contents for BTS 1030-8339

Reviews:

Related manuals for BTS 1030-8339

Brands by name

Popular brands

Wacker Neuson BTS 1030-8339, Repair Manual

Search results

Summary of Contents for BTS 1030-8339

Reviews:

Related manuals for BTS 1030-8339

Brands by name

Popular brands