background image

10 Use and operation

37

10.5

Operating the machine

Processing material

1. Hold the machine firmly with both hands.
2. Place the tool into position on the material.
3. Press down the gas handle.
4. With both hands, press the machine against the material to be processed.

Note: 

Press with sufficient strength that you feel the machine's spring sys-

tem, but not the lower stop.

5. When the material has been processed, lift and adjust the machine.

Note: 

Proceed as follows if the tool gets stuck in the material:

„

Open the tool holder and remove the tool.

„

Continue working with another tool.

„

When the machine is lifted and the gas handle is pressed, the engine contin-
ues to run at a high speed, while the percussion system remains engaged. 

„

When the tool has no resistance, the percussion system goes over to idle op-
eration and no longer impacts.

Note for breaking off edges

Pay attention to the following points when breaking off edges:

„

Vertical stability.

WARNING

Injuries from insufficiently guided or uncontrolled machine.

f

Always hold machine with both hands and stand firmly.

Item

Designation

1

Gas handle

Summary of Contents for BH23





































































Reviews: