background image

wagtx5700000028en.fm

15

AD ...

Malfunctions, causes and remedies

8.

Malfunctions, causes and remedies

Malfunction

Cause

Remedy

The machine does not start

No electric power

Check the function and position 
of the main switch

Check the ratings of the electri-
cal power line (230 V 1 ~ 
50 Hz)

The moisture meter is incor-
rectly set

Set the moisture meter so that 
the value is smaller than the 
current value of the relative 
humidity in the room

The machine does not start

Water collecting pan is full 
(control lamp (c) is lit)

Empty the water collecting pan

Fan and compressor are in 
operation but there is no forma-
tion of water and ice on the 
evaporator

Insufficient air supply

Check if there are objects 
obstructing the suction and dis-
charge side

Check if there are any deposits 
or incrustations on the filter or 
on the cooling fins of the con-
denser or evaporator

Values for the temperature and 
relative humidity are too low

Check if the temperature is 
between 0 °C and 40 °C and if 
the relative humidity is between 
40 % and 100 %

The cooling circuit does not 
function properly

Contact the Technical Cus-
tomer Service

The machine has switched off, 
and the control lamp (c) is lit

Water collecting pan is full

Empty the water collecting pan

The machine has switched off 
and the control lamp (b) is lit 
(the cooling fins of the con-
denser have overheated)

Air flow path is obstructed

Remove any obstructions and 
turn the machine back on

Room temperature is over 
40 °C

Do not start the machine until 
the temperature has fallen 
below 40 °C

The fan motor is defective

Contact the Technical Cus-
tomer Service

The cooling circuit does not 
function properly

Contact the Technical Cus-
tomer Service

The machine has switched off, 
and the control lamp (b) is lit

Temperature is below 3 °C

Place the air dehumidifier in a 
room that has a temperature of 
3 °C

Summary of Contents for AD Series























Reviews: