WACKER Group DPU 25..H.. Page 33 Operator'S Manual Download

Page: 33 / 36

Prüf- und Zertifizierungsinstitut

VERBAND DER ELEKTROTECHNIK

ELEKTRONIK INFORMATIONSTECHNIK e.V.

C E R T I F I C A T E

Registration-Number: 6236/QM/06.97

This is to certify that the company

Wacker Construction Equipment AG

Wacker-Werke GmbH & Co. KG

at the following locations

Head Office Munich

Preußenstraße 41

80809 Munich

Production plant Reichertshofen

Karlsfeld logistics centre

Sales regions with all branches all over Germany

has implemented and maintains a

ality

anagement

ystem for the following scope:

Machine manufacture

Construction machines

This Q System complies with the requirements of

DIN EN ISO 9001:2000

and the requirements of the German and international Road Traffic Act.

This Certificate is valid until 2009-06-05.

VDE Testing and Certification Institute

Certification

Date: 2006-05-30

63069 Offenbach, Merianstraße 28
Telefon: +49 (0) 69 83 06-0, Telefax: +49 (0) 69 83 06-555
E-Mail: [email protected], http://www.vde-institut.com

The VDE Testing and Certification Institute is accredited by DAR Accreditation
Bodies according to DIN EN ISO 17020 and DIN EN ISO 45012 and notified in the EU
under ID.No. 0366.

TGA-ZM-09-92-00
KBA-ZM-A 00021-97

DIN EN ISO 9001 Certificate

Summary of Contents for DPU 25..H..





































Search results

Summary of Contents for DPU 25..H..

Reviews:

Related manuals for DPU 25..H..

Brands by name

Popular brands

WACKER Group DPU 25..H.., Operator'S Manual

Search results

Summary of Contents for DPU 25..H..

Reviews:

Related manuals for DPU 25..H..

Brands by name

Popular brands