WACKER Group DPU 25..H.. Operator'S Manual Download | Manualshive

Page: 15 / 36

background image

Description

T00978GB.fm

15

4.3

Max. admissible inclination

4.4

Description of function

4.4.1

The vibration required for compaction is produced by the exciter (5)
which is firmly joinded to the lower mass (4). This exciter (5) is
designed as a central vibrator with aligned vibrations. Such a principle
permits the direction of vibration to be changed by turning the eccentric
weights (13). In this way an infinitely variable transition between
vibration in forward motion, at standstill and in reverse motion is
possible.
This process is hydraulically controlled with the operating control
handle (7) on the centre pole head (8).

«
...
13
14
15
16
17
...
»

Summary of Contents for DPU 25..H..





































Reviews:

No comments

Related manuals for DPU 25..H..

Brand: RAMSET Pages: 18

Brand: Eastwood Pages: 12

Brand: Eastwood Pages: 8

Brand: Earlex Pages: 8

Brand: Earlex Pages: 5

Brand: Farm King Pages: 94

Brand: FAR Pages: 12

Brand: FAR Pages: 80

Brand: Icom Pages: 2

Brand: Labounty Pages: 2

Brand: Labounty Pages: 52

MAG-8200 Series

Brand: Magna-Matic Pages: 38

Brand: Camo Pages: 7

Strong-Arm CLL500

Brand: Clarke Pages: 8

Brand: KABI Pages: 6

Brand: Gardner Denver Pages: 27

Brand: Eastwood Pages: 16

CONTRACTOR 6462121

Brand: Clarke Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands