background image

WEL/ IM/ 05/ 18.03.2016 

 

15 

 

 
 

 

For cleaning of Modules Fresh water (TDS < 1500 mg/l) may be used. If needed, a mild, non-abrasive, 

non-caustic detergent with a final fresh water and detergent solution mix between 6.5 < pH < 8.5 at 25°C 
may be used. 

 

When  using  water,  RO  water  provides  the  best  results.  In  absence  of  RO  water,  tap  water  with  low 

mineral content (total hardness <75 mg/l) or deionized water may be used. Calcium should not exceed: 
75  mg/ml.  Do  not  use  solutions  containing  hydrochloric  acid,  D-Limonene,  ammonia  or  sodium 
hydroxide. 

 

Clean the Module either with a soft sponge or a soft rubber wiper. Do not use abrasive cleaners or de- 

greasers on the Module. Do not scrub the Module with abrasive brushes. Such brush fibers may scratch 
the glass, reducing the power output of the panel. 

 

In case if soft water (with low mineral content) is not available, Module can be dry cleaned with the help 

of a soft cloth or with soft sponge to remove dirt, dust. One can also use wet cloth, sponge to clean dirt 
which is not easily removed by dry cleaning. 

 

Do not clean or spray water at the Junction Box or any area on the backside of the Module. 

 

Frequency of Cleaning will vary depending upon any special conditions in  the area where the Modules 

are installed. Modules installed in high windy or dusty areas should be inspected more frequently. 

 

If excessive soiling is present, a non-conductive soft brush, sponge, or other mild agitating method may 

be used before using water. Ensure brushes or agitating tools are not abrasive to glass. 

 

Module damage that arises as a result of improper cleaning will not be warranted by WAAREE Energies 

Ltd. 

 

Do not clean the glass surface with chemicals. Do not let water stay on the glass surfaces of PV Modules 

for  a  long  time.  This  creates  a  risk  of  permanent  damage  to  the  glass,  such  as  white  efflorescence, 
otherwise known as “glass disease,” which may cause reduced power output. 

 

To avoid dirt accumulation or white efflorescence due to water accumulation, do not install PV Modules 

horizontally (flat). 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WAAREE ENERGIES LIMITED

 

602, Western Edge-I, Off. Western Express Highway 

Borivali (E), Mumbai 400066, Maharashtra, India 

Tel: +91-22-66444400 

[email protected]

 

 

 

 

 

 

 

 

Summary of Contents for PV Modules
















Reviews: