background image

 

Technical Specifications 

Body

Optical Body, inclined 30

°

, able to rotate a full 360

°

with  

53mm to 75mm interpupillary adjustment. Left Eye diopter 

adjustment of -5 to +5. 

Nosepiece:

 

Quintuple  ball-beating reversed nosepiece with positive click 

stops and smooth operation. 

Eyepieces:

 

10X Plan wide field, Focal Length 25mm, Field 

Φ

18mm. 

Stage:

 

Integrated Mechanical Stage size 185mm X 140mm with Glass 

insert 98mm X 77mm. Right–hand Coaxial drop–down X–Y 

Control Knobs. Range of motion 75mm X 50mm. 

Focus Mechanism: 

All stainless steel and brass gear train system 

Adjustable Tension Control to prohibit drift and Adjustable 

Up-Stop to protect slides, specimen and objective lenses. 

Coaxial coarse and fine adjustments with dial markings at 

0.002mm increments. 

Incident Light System: 

Condenser, Field and Aperture Iris diaphragm,   

four color Filter Wheel and Polarizing filter 

Transmitted Light System:  

1.25 N.A., Abbe Condenser with iris diaphragm   

             Rack and Pinion Focusing, Easily centered with two adjustment 

knobs. 

Illumination:

 20 watt, 6 volt Halogen bulb with electronic dimmer  for 

Incident and Transmitted light systems. Fuse: 0.5 Amp, located 

in the base 

 

 

 

 

 

 

 

Summary of Contents for VistaVision 82026-636

















Reviews: