background image

Page 22

SECTION 10

LIMITED WARRANTY

Every VuQube Satellite System is thoroughly inspected and tested before leaving the factory.  
It is covered by a one year parts limited warranty from the date of original purchase.  This
warranty does not cover installation and external wiring or refurbished units.

Should any trouble develop during the warranty period, contact King Controls.  Only King
Controls may perform warranty evaluations and repairs.

If it is determined that the unit needs to be returned, return COMPLETE product, freight 
prepaid, to: 

King Controls, 11200 Hampshire Ave. S. Bloomington, MN 55438-2453

.

If inspection shows the trouble is caused by defective workmanship or material, King Controls
will repair the unit without charge.

This warranty does not apply where:

• The product has been abused, misused, improperly installed or improperly maintained.
• Repairs have been made or attempted by others.
• Repairs are required because of normal wear and tear.
• Alterations have been made to the product.

In no event shall King Controls be liable for any indirect, incidental, or consequential
damages from the sale or use of the product.  This disclaimer applies both during and
after the term of the warranty.

King Controls disclaims liability for any implied warranties, including implied
warranties of “merchantability” and “fitness for a specific purpose,” after the one year
term of this warranty.

This warranty gives you specific legal rights, and you may also have other rights, which vary from
state to state.  Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.  Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Summary of Contents for VQ4000





























Reviews: