Vulcan-Hart GR Series Service Manual Download Page 55 | Manualshive

Page: 55 / 56

background image

Page 55 of 5

6

F35660

Rev. A (0717)

KLEENSCREEN FILTERING SYSTEM

Symptom

Possible Causes

Shortening not filtering, pump motor is on.

1.

Filter screen is plugged.

2.

Clog in filter system lines.

NOTE:

If using solid shortening, when all filtered shortening is

returned to the fry tank and filter power switch is off, open the
filter drawer approximately 1 inch. Allow the remaining
shortening in the line to drain into the filter tank to prevent
possible clogging after the shortening cools and solidifies. Close
the filter drawer when complete.

3.

Shortening below 300°F too thick.

4.

R2 fill relay malfunction (N.C. contacts are open).

5.

Fill solenoid valve malfunction.

6.

Interconnecting wiring malfunction.

7.

Pump is inoperative.

Shortening not discarding, pump motor is on.

1.

Filter screen plugged.

2.

Clog in filter system lines.

NOTE:

If using solid shortening, when all filtered shortening is

returned to the fry tank and filter power switch is off, open the
filter drawer approximately 1 inch. Allow the remaining
shortening in the line to drain into the filter tank to prevent
possible clogging after the shortening cools and solidifies. Close
the filter drawer when complete.

3.

Shortening below 300°F too thick.

4.

Discard valve switch malfunction (N.O. contacts not closing to
energize R2 relay coil).

5.

R2 fill relay malfunction (contacts remain closed).

NOTE:

The fill solenoid valve should not be energized during

discard operation so that shortening will flow through manual
discard valve only.

6.

Discard valve mechanical malfunction.

7.

Discard hose connection not fully engaged.

8.

Pump is inoperative.

Pump motor is not running to circulate
shortening through filtering system, display is
lit.

1.

Filter key on control panel not pressed or held in long enough
to start pump motor (default is 3 sec.).

2.

R1 pump motor relay malfunction.

3.

Cooking control malfunction.

4.

Interface board malfunction.

5.

Interconnecting wiring malfunction.

6.

Pump motor inoperative.

GR Series Gas Fryers with NCC Controls (formerly Tridelta / Built after 3/05) - TROUBLESHOOTING

«
...
53
54
55
56
»

Summary of Contents for GR Series

























































Reviews:

No comments

Related manuals for GR Series

Brand: UFESA Pages: 72

Brand: Admiral Pages: 4

Brand: OMEGA AIR Pages: 37

Brand: Blomberg Pages: 4

Brand: Rupes Pages: 12

Brand: V-ZUG Pages: 32

Brand: GE Pages: 12

Brand: GE Pages: 16

Brand: GE Pages: 3

Brand: GE Pages: 3

Brand: GE Pages: 3

Brand: GE Pages: 23

CleanSpeak GTD81ESSJWS

Brand: GE Pages: 36

Brand: GE Pages: 56

CleanSpeak GTD81ESPJMC

Brand: GE Pages: 36

Brand: GE Pages: 24

Appliances Profile PFDN440

Brand: GE Pages: 156

CleanSpeak GTD81ESPJMC

Brand: GE Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands