background image

 

 
This warranty applies only to units used in residential non-commercial use. The 
warrantor assumes no liability for property damage or any other incidental or 
consequential damage whatsoever which may result from failure of this product. Any 
and all warrantees of merchantability and fitness implied by law are limited to the 
duration of the expressed warranty. All warrantees apply only to VTL products 
purchased and used in the USA, and are only applicable within the USA. Products 
purchased outside the USA may not be registered for warranty with the factory in the 
USA, but may only be registered with the VTL distributor in the country of purchase. 
In the case of returns from outside the USA, the owner of the product returned is 
responsible for all shipping charges, and VTL will accept no shipping or customs duty 
charges for goods returned to the USA, nor any shipping or customs duty charges for 
the return of the product to the owner. 
 
Some states do not allow limitations on how long an implied warranty lasts, so the 
above limitations may not apply to you. Some states do not allow the exclusion or 
limitation of incidental or consequential damages, so the above exclusion may not 
apply to you. This warranty gives you specific legal rights and you may also have other 
rights that vary from state to state.

 

TL5.5 SERIES II Preamplifier Owner’s Manual 
VTL 

52 

 

Summary of Contents for TL5.5 Series II Signature



























































Reviews: