background image

 

X4,AUX5,TAPE 

>COUNTDN 
{ON|OFF}

 

For toggling between 
muting and unmuting 
the power up 
countdown

 

Returns current countdown status. 

>

DSPLYOFF [n]  For automatically 

turning off the display 
after last command after 
programmed number of 
seconds 0 – 99, with 00 
for always on. 

Returns current time, in seconds, that 
display will shut off after last command, 
for example: 

>DSPLYOFF 00 

>LOCKOUT 
[ON|OFF] 

For toggling between 
front panel locked and 
unlocked. 

>LOCKOUT OFF for unlocked front 
panel 

>LOCKOUT ON for locked front 
panel 

>VTL

 

Returns factory contact 
info

 

Contact VTL: 

Email: 

[email protected]

Tel. 909-627-5944 

Fax. 909-627-6988 

>VERSION 

Returns the version 
number of the software. 

Installed version of the software: 

>Version 072109 

 

Powering the system off 

You may keep your VTL preamplifier and your source components on permanently if you 
prefer to keep them warm. If you prefer to keep all your equipment off when not in use 
then it is best to follow the correct turn off sequence to avoid power off thumps through 
the system. (If the power fails or if you accidentally turn off the preamp before turning the 
power amplifiers off, the preamplifier will power down in a muted state and no damage 
will be done to your system.) 

1.  When you’re done listening to your system always turn your power amplifier(s) off 

first, if not using the trigger function on the TL5.5. 

TL5.5 SERIES II Preamplifier Owner’s Manual 
VTL 

39 

 

Summary of Contents for TL5.5 Series II Signature



























































Reviews: