manualshive.com logo in svg

VQ Model VQA09, Building Instructions, Page: 3 / 12

Share
Download
VQ Model VQA09 Building Instructions Download Page 3

A B

A B

! Make sure to glue
 securely, If not properly 
glued, a failure in flight may
occur.

Trial fit each part before gluing . Be certain that there 
are no gaps. If the parts will join,
but with a gaps, sand or trim the parts a little at a time until
 the parts meet exactly with no gaps.
Check for the correct dihedral  angle

Carefully slide the wing halves together, ensuring that they are 
accurately aligned, Firmly press the two halves together, 
allowing the excess epoxy run out.

When joining the wing halves it is extremely important to use 
plenty of epoxy (30 minutes epoxy).

Use epoxy glue to bury the opening

WING TOP-VIEW

1-

Joining the wing / Flachenverbindung

IMPORTANT:

Please do not clean off the excess epoxy on the wing 
with strong solvent or pure alcohol, only use kerosene 
to keep the colour of your model not fade.

Secure one end of the 
thread  with adhesive tape

Secure one end of the 
thread  with adhesive tape

Binder clip

Nylon wing bolt

Rubber band
(both the top
and bottom)

2- 

Aileron Servo extension cord

 

BOTTOM VIEW

Carefully, to link the end of the thread
to the aileron servo extension cord before
to install the aileron servo to the wing.

Thread

Thread

*Servo Extension Standard 500mm
CJ0500STD

X

X

3- 

Aileron Servo / Querruder servo

 

BOTTOM VIEW

Adhesive 
tape

Summary of Contents for VQA09













Reviews:

No comments