background image

 

 

Playing Records 

Before playing a record, make sure that all of the tonearm screws are tight.  

Place the black washer on the platter, then the record, then the record clamp.  
Always turn off the turntable before installing the record clamp. 

Press the power button on the motor. Sit down and enjoy listening to your 

records! 

 

General Use 

 

Allow at least 20 hours of break-in time.  

 

The motor will make some low-level noise. This will not get into the 

system. The motor and bearings will become quieter as you use your 
Scout.  Place the motor on a mouse pad for better isolation 

 

If you notice hum in the system, remove the turntable to phono section 
interconnects and replace them with very cheap, standard VCR 

interconnects. These are well shielded and should eliminate the hum. If the 
hum goes away, get quality, well shielded interconnects. 

 

After at least one year of use, the platter bearing and motor will need to be 
lubricated. For the platter, use a ¼” blob of white lithium grease placed on 

the ball.  For the motor, use 1 drop of 40-weight motor oil below the black 
drive pulley and right on the brass piece. 

 

We find the table sounds best with no mat on the platter, you can 
experiment with mats but you need to adjust the VTA setting when doing 

this. 

 

Summary of Contents for Scout/JMW-9T











Reviews: