background image

Additional Items Available from Your Dealer 

 

The VPI Synchronous Drive System power supply provides a major increase 

in musicality by feeding the synchronous motor in your table a perfectly 
stable wave form at the frequency you choose. The SDS lets you change 
speed electronically. 

 

300 RPM Scoutmaster motor - $150.00 

 

Classic aluminum platter - $800.00 

 

TNT-Mini isolator feet - $300.00 

 
 
 

VPI Industries, Inc. Limited Warranty 

VPI Industries, Inc. (VPI) warrants this unit against defects in materials and/or 
workmanship for three (3) years from the date of purchase by the original retail 

purchaser. VPI’s sole obligation under this warranty is limited to the repair or 
replacement, at VPI’s option, of any part(s) found to be defective. VPI’s 
obligation to repair or replace defective parts is the purchaser’s sole and 
exclusive remedy, and VPI shall not be liable for any direct or indirect injury 

and/or property damage arising out of the use of the product or defect in or 
failure of the product.  

This warranty does not extend to any unit whose serial number has been defaced 
or altered. Any product that VPI determines causes a defect or malfunction due 

to incorrect installation, modification, misuse, or servicing by the purchaser, or 
service technician not authorized by VPI to perform such service will not be 
warranted. This warranty does not cover trivial or cosmetic defects that do not 
impair the unit’s normal function. 

VPI reserves the right to make changes in this product without assuming any 
obligation to install such change in any product previously manufactured. This 
warranty to repair or replace defective parts is in lieu of all other express or 
implied warranties of merchantability or fitness for a particular purpose. There 

are not warranties that extend beyond the description herein. 

Some states do not allow exclusion of implied warranties or limitation of 
incidental or consequential damages, so the above exclusion or limitations may 
not apply to you. This warranty gives you specific legal rights, and you may also 

have other rights that vary from state to state.

  

Summary of Contents for Scout/JMW-9T











Reviews: