background image

128-9353

14 of 16

Page 14

Diagnostics:

Enter Bank 3 and turn on selectable feature # 7 as described in the feature selection 

and setting section.

Exit the feature selection mode then press and hold the pushbutton valet/program switch 

and then turn the ignition switch to the on position.

NOTE: 

  Diagnostic mode is a temporary mode. Once you have accessed the diagnostic 

mode, the unit will pause for two seconds then begin to flash the last stored 

shut down code. This code will be displayed three times in succession, then 

the unit will automatically exit the diagnostic mode.

The parking lights will flash a number of times indicating the reason for the last remote 

start shutdown. The light flash indications are as follows:

1 Flash  

Run timer expired

2 Flashes 

Low or no tach signal (RPM)

3 Flashes 

Positive inhibit wire activation

5 Flashes 

RF shutdown signal received, or manual start trigger wire reactivated.

6 Flashes 

High tach signal (RPM)

7 Flashes 

Tach signal has not been learned

8 Flashes  

Negative inhibit wire activation

4 PIN DATA BUS PORT (DBI Port)

The 4 pin port located on the side of this module is for proprietary Audiovox data bus 

interface modules. These modules are used to access a variety of features in the vehicle 

which can be as simple as door trigger inputs, to more complex door lock outputs, or 

transponder interfaces for remote starting. DO NOT connect anything to this port other 

than the Audiovox DBI interface modules or damage to the Remote Start will occur. 

All installation instructions for the DBI modules will be packaged with the individual 

component along with the proper 4 pin wiring harness requires to access the data 

transmit & receive as well as the proper voltage levels for the interface.

Summary of Contents for Pursuit PRO9051E

















Reviews: