Voxx Pursuit PRO9051E Install Manual Download

Page: 11 / 16

128-9353

11 of 16

Page 11

SELECT

ABLE FEA

TURES

The selectable features of this unit can be set manually as explained on the previous page.

Factory default settings are indicated by

BOLD

text below

NOTE:

Manual programming Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indic

ated.

Also, no data will be indicated if a feature is not available for a particular model.

The unit will enter the feature but no selection will be available.

Feature Selection

1 Chirp

2 Chirps

3 Chirps

4 Chirps

5 Chirps

6 Chirps

1st DoorL/UL

1S/1S

3.5 Sec.

500mS L, Dbl. U/L

Dbl L, 500mS UL

Dbl L, Dbl UL

500mS/350mS ul

2nd Accy

Lock

Not A

vailable

3rd Accy

. UL

Not A

vailable

4th Headlights

Not A

vailable

5th Passive Locks

Not A

vailable

6th

Pass/Act

Arm

Not A

vailable

7th Siren/Horn

Not A

vailable

8th Horn Chirp

Not A

vailable

9th O/R Method

Not A

vailable

10th 2 Step U/L

Not A

vailable

11th Chp Del

Not A

vailable

12th

Trigger

Circuits

Not A

vailable

13th L/UL

Poll

Not A

vailable

14th

Aux Ch 5 Sel

Not A

vailable

15th

Aux Ch 6 Sel

Not A

vailable

16th

Aux Ch 7 Sel

Not A

vailable

17th T

rigger

Delay

Not A

vailable

18th DBI/ADS Select

Not A

vailable

Summary of Contents for Pursuit PRO9051E

















Search results

Summary of Contents for Pursuit PRO9051E

Reviews:

Related manuals for Pursuit PRO9051E

Brands by name

Popular brands

Voxx Pursuit PRO9051E, Install Manual

Search results

Summary of Contents for Pursuit PRO9051E

Reviews:

Related manuals for Pursuit PRO9051E

Brands by name

Popular brands