vonado 42111 Manual Download Page 11 | Manualshive

Page: 11 / 25

background image

Take a warm white 15cm dot light, two 15cm headlights, a trans orange 1x1 round plate, repeat
the previous steps to install the other 2 headlights.
Take a 50cm connecting cable, connect it to the expansion board.

Thread the connecting cable to the bottom, thread the cable through the following space.

Pull the cable backward.

«
...
9
10
11
12
13
...
»

Summary of Contents for 42111


























Reviews:

No comments

Related manuals for 42111

Brand: Cooper Lighting Pages: 1

Brand: Forch Pages: 18

Brand: PowerSmith Pages: 16

Brand: OttLite Pages: 2

Brand: EuroLite Pages: 14

Exterior 1200 Wash

Brand: Martin Pages: 84

Brand: shada Pages: 16

Brand: ALW Pages: 12

Micronex 70W HPS

Brand: Chalmit lighting Pages: 7

EPL-EMG-HB-50LED-RT-WLM

Brand: Larson Electronics Pages: 3

Brand: Phenom Pages: 2

Astral Extreme AS-X-400

Brand: impact Pages: 24

SMARTERHOME KAE14CWWT1A

Brand: Kogan Pages: 24

Intimidator Spot 455Z IRC

Brand: Chauvet Pages: 27

Brand: LEDLITE Pages: 2

Brand: Strend Pro Pages: 27

Brand: Lightolier Pages: 1

Brand: Lightolier Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands