Volvo TAD420VE Operator'S Manual Download Page 46 | Manualshive

Page: 46 / 62

background image

Felkoder

44

PID 48, Code 2.9.2 Atmospheric pressure

Reason:

Air pressure is outside permissible values.

Reaction:

A fault code is generated. The fault code

disappears when the pressure returns to normal.

Monitoring function for air pressure is activated.

Action:

• Turn the ignition off and on, and check if the fault

code remains.

SID 253, Code 2.10.1 Parameter fault

Reason:

No data or incorrect data (fault only occurs

during parameter setting or reset).

Reaction:

Engine can not be started.

Action:

• Check parameter settings.

• Turn the ignition off and on, and check if the fault

code remains.

SID 240, Code 2.10.1 Stack overflow

Reason:

Internal calculation fault.

Reaction:

The engine is emergency stopped and

can not be re-started until the fault is rectified.

Action:

• Turn the ignition off and on, and check if the fault

code remains.

«
...
44
45
46
47
48
...
»

Summary of Contents for TAD420VE































































Reviews:

No comments

Related manuals for TAD420VE

Brand: ABB Pages: 8

MICROPUMP EagleDrive MS

Brand: Idex Pages: 23

Brand: Polini Pages: 32

Brand: Grundfos Pages: 25

Brand: Shindaiwa Pages: 44

Brand: Plettenberg Pages: 26

MaxxForce DT 10

Brand: Navistar Pages: 109

Brand: Deutz Pages: 37

Brand: Raider Pages: 193

Brand: Texas Equipment Pages: 38

Brand: Texas Equipment Pages: 57

Brand: Texas Equipment Pages: 60

Brand: KAZZ Pages: 11

Brand: YS Pages: 2

Brand: YS Pages: 2

ZA top SM225.40B

Brand: ZIEHL-ABEGG Pages: 76

Brand: Honda Pages: 45

Brand: Novy Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands