Volvo TAD420VE Operator'S Manual Download Page 17 | Manualshive

Page: 17 / 62

background image

Starting the engine

15

Never use start spray

WARNING!

Never use start spray or similar

products as a starting aid. Explosions could oc-
cur in the inlet manifold. The consequence could
be personal injury.

Starting with auxiliary batteries

WARNING!

Batteries (especially auxiliary bat-

teries) contain hydrogen which is highly explo-
sive in contact with air. A spark, which can be
formed if the auxiliary batteries are wrongly
connected, is enough to make a battery explode
and cause damage.

1. Check that the auxiliary batteries are connected

(series or parallel) so that the rated voltage cor-
responds to the engine system voltage.

2. First connect the red (+) jumper cable to the

auxiliary battery, then to the flat battery. Then
connect the black jumper cable (–)

to the auxil-

iary battery, and lastly to a place

some distance

from the flat batteries

, such as the negative

cable by the main switch or the negative cable
connection on the starter motor.

3. Start the engine.

WARNING!

Do not move the connections when

you attempt to start the engine (risk of arcing),
and do not stand and lean over one of the bat-
teries.

4. Remove the jumper cables in the reverse order

from installation.

WARNING!

The ordinary cables to the standard

batteries must not be loosened on any condi-
tion.

«
...
15
16
17
18
19
...
»

Summary of Contents for TAD420VE































































Reviews:

No comments

Related manuals for TAD420VE

Brand: Atlas Copco Pages: 156

Brand: Man Pages: 136

Brand: Lenze Pages: 76

Brand: Kubota Pages: 47

Brand: Kubota Pages: 181

AG2210-LP Series

Brand: Beckhoff Pages: 35

Brand: Volvo Penta Pages: 44

Brand: Volvo Penta Pages: 90

Brand: YS Pages: 2

Brand: Yanmar Pages: 316

Brand: Motion Pages: 124

B&W S50ME-B9.3-TII

Brand: Man Pages: 337

Brand: Man Pages: 353

Brand: Man Pages: 375

Brand: wsm Pages: 124

Brand: Kyosho Pages: 4

USB Protocol Suite

Brand: LeCroy Pages: 107

Brand: ePropulsion Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands