Volvo MD2010 Workshop Manual Download Page 25

Page: 25 / 81

Repair instructions

Cylinder head
Dismantling of cylinder head

Remove both battery leads. Close the fuel cocks.

Close the bottom valve and drain off the water in

the sea and fresh water system.

Release the hose to the heat exchanger from the

sea water pump. Release the exhaust pipe from

the exhaust hook.

Fig. 9. Dismantling of expansion tank with heat ex-

changer

Release the thick rubber hose under the heat ex-

Heat exchanger complete

changer.

(Note:

the hose is filled with refrigerant).

Spring

Release the thin hose from the refrigerant pump.

3. MD2o10,

Thermostat

Release the electric cables to the oil pressure relay

and to the refrigerant temperature relay and sensor

(where appropriate).

: remove the cover at the front on the heat

exchanger housing's right-hand side. Remove the

spacer ring, thermostat and rubber seal.

Engine body

11. Release the delivery pipe at the injection pump

and injectors. Lift off the delivery pipes together.

Protect the connections from impurities.

12. Remove the nut at the top of respective injectors

and lift off the fuel leak pipe.

: remove the drive belt for the al-

ternator/refrigerant pump. Remove the alternator

and clamp.

Remove the expansion tank complete with heat ex-

changer.

: Remove the spring, thermostat

and rubber seal from the heat exchanger housing.

10.

Remove the induction manifold.

Release the relay box from the heat exchanger

housing and hang it up.

Remove the inlet pipe complete with air filter.

Summary of Contents for MD2010


















































































Search results

Summary of Contents for MD2010

Reviews:

Related manuals for MD2010

Brands by name

Popular brands

Volvo MD2010, Workshop Manual

Search results

Summary of Contents for MD2010

Reviews:

Related manuals for MD2010

Brands by name

Popular brands