manualshive.com logo in svg

Volvo ECR 58, Translation Of The Original Instructions, Page: 8 / 41

Share
Download
Volvo ECR 58 Translation Of The Original Instructions Download Page 8

© Rototilt Group AB

2018-03-16

EN

English

Detach the tool

Position the tool horizontally, resting on 

firm ground or so that the tool cannot 

slide out of the attachment when the 

quick coupler locks are opened. 

!

IMPORTANT 

- If the tool can fall or change position in 

connection with the procedure, there is a risk of damaging 

the tool and/or quick coupler.

!

IMPORTANT 

- It is only possible to open the lock when 

the start menu is visible or from the troubleshooting menu.

Operating Rototilt® Quick coupler

Check that the display shows the start 

menu.  The icon for the quick coupler 

locking function is shown above the 

green function key.
First press the green function key and 

release it.  

The buzzer sounds.
Now move the quick coupler locking 

function switch to the open position.  

The switch is enabled for a period of 10 

seconds. 
The lock remains open as long as the 

switch remains open, but pressurising 

is only performed during the preset time 

period, 3-12 seconds. 

The selected time can be checked on the 

display, 

Menu settings

. 

The switch must be switched on and then 

off again to repressurise the hydraulic 

cylinder.  

See the 

Instructions for Use

 for the quick 

coupler

.

2200397_        _6909

Summary of Contents for ECR 58










































Reviews:

No comments