14
– Remove the towbar by pressing in the lock knob and
turning it down until a click is heard.
– Turn the lock knob down further, right to when it stops,
hold the lock knob down and pull out the ball section.
15
– Clean away any underseal and dirt from the surfaces
between the towbar and the bodywork.
The illustration shows how the towbar and its components
are assembled and installed on the body.
16
– Install the screws (7, 8) from underneath the brackets
(4:1, 5:1, 9:1), including the sleeves (6). Tighten by
hand. The arrows on the brackets (4:1, 5:1, 9:1) must
point in towards the centre of the car. Carry out on
both sides, the right-hand side is illustrated.
17
Illustration A
Illustration B
Carry out in accordance with illustration A and B
– Install the heat deflector plate (14) using the screw
(12).
– Loosely screw the heat deflector plate into place on
the member (2) using the screw (1).
– Bend the heat deflector plate using a screwdriver.
– Fully screw in the screw.
– Reinstall the rubber mounting (13) for the silencer.
Use normal soap to facilitate installation.
18
– Insert the member (1) between the brackets (4, 5) and
centre around the holes.
– Install the screws (2) and washers (16) from
underneath the bracket (5) and the nuts (3) from
above, without tightening.
19
– Tighten the screws (7) to
79 Nm (58 lbf.ft.)
.
– Tighten the screws (8) to
120 Nm (89 lbf.ft.)
.
– Carry out on both sides, the right-hand side is
illustrated.
20
– Tighten the screws (2) and nut (3) to
136 Nm (100
lbf.ft.)
.
– Wait for at least five minutes so that the joint has time
to set. Then tighten the screws (8) on both sides, a
quarter turn (angle tightening 90°).
NOTE! Torque tightened screws that have been
removed must not be re-used.
21
– Underseal.
Applies to Sweden only
– Underseal after the state roadworthiness inspection.
22
Applies to cars up to and including model year –2004
(CH -458999)
–
Applies if the car has moulding:
Reinstall the
mouldings (3) on the expander screws and press
them in.
– If the guide lugs (4) and clips (5) have loosened –
reinstall them.
–
Applies to cars with parking assistance:
Lift up
the bumper in position. Pull the cable for the sensors
through the hole for the bumper’s guide, and pull the
cable in from the inside.
– Reinstall the bumper by pressing it forwards. Ensure
that the four screws, protruding from the bumper, align
with the holes in the car.
– Before the bumper is completely installed, slide the
top edge (1) into the grooves. Then slide the bumper
fully in.
– Check that the guide lug (4) and clip (5) are centred
with the hole (2) in the wheel arch liner.
23
Applies to cars up to and including model year –2004
(CH -458999)
– Tighten the screw (1) on both sides.
– Rivet (2) the bumper into place as illustrated.
– Reinstall the nuts. Tighten the nuts. Tighten to
18 Nm
(13 lbf.ft.)
.
– Connect the antenna connector.
Applies to cars with rear mudflaps
– Rivet in the mudflap.
– Reinstall the wheels and tighten the screws alternately
to
110 Nm (81 lbf.ft.)
.
24
Applies to cars from and including model year 2005-
(CH459000-)
–
Applies to cars with parking assistance:
Lift up
the bumper in position. Pull the cable for the sensors
through the hole for the bumper’s guide, and pull the
cable in from the inside.
– Guide the hooks (1) for the bumper into the guides (2)
in the side brackets. Press at the upper edge and in
the middle so that the hooks engage.
2006 12 31213957