manualshive.com logo in svg

Volvo 242 1977, Manual

Share
Download
Volvo 242 1977 Manual Download Page 53

WWW.MANUALS.WS 

 

 

 

 

 

 

 

WWW.MANUALS.WS 

1977 Volvo 242 244 245

driving long distances at high speeds, extended periods of idling or low speed operation, short trip 
operation at freezing temperatures oil changes are required more frequently (every three months). 
Drain the oil after driving while it is still hot.  
Capacity excl. filter 3.5 US qts/3.0 Imp. qts. 
incl. filter 4.0 US qts/3.4 Imp. qts. 

 

Changing oil filter 
Replace the oil filter at every oil change. If the oil filter for any reason is changed separately 1/2 qt. of 
oil should be added. 

pg. 49 Cooling system 

 

Changing coolant 
Every two years or 30,000 miles the cooling system should be drained, flushed and refilled.  
Remove the expansion tank cap. 
Loosen the hose at the bottom of the radiator and open the drain cock on right side of the engine block.

Fill coolant through the expansion tank. 

file:///K|/ownersdocs/1977/1977_242_244_245/77242244245_03a.htm (8 of 16)12/22/2006 10:07:32 PM

Summary of Contents for 242 1977










































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands