VOLTCRAFT 2362387 Operating Instructions Manual Download Page 5 | Manualshive

Page: 5 / 35

background image

5

4. Delivery contents

•  Device tester GT-6000 v2
•  1 mains cable (IEC 60320 C19)
•  1 test lead with alligator clip
•  1 IEC power cable (IEC adapter cable IEC 60320 C13)
•  1 USB-C connection cable (USB-A connector to USB-C socket)
•

6 AA batteries,1.5 V (type AA/LR6)

•  1 lithium button battery (CR2032)
•  1 pouch
•  Operating instructions

Up-to-date operating instructions

Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR

code. Follow the instructions on the website.

5. Optional accessories

Passive measurement adapter:

Single and three-phase loads adapter are intended for R

PE

, R

ISO

and I

EA

measurements (without mains voltage-

dependent switching device). Commercially available measurement adapters with the following connections can be

used:
16 A CEE connector (5-pin, L1, L2, L3 are bridged) --> earthing contact connector.

Active measurement adapter:

Three-phase loads adapter for R

PE

and IPE measurements (direct measurement, with mains voltage-dependent

switching device) under operating conditions:
16 A CEE adapter (5-pin), active
The active measurement adapter can be obtained using item no. 2267357.

«
...
3
4
5
6
7
...
»

Summary of Contents for 2362387




































Reviews:

No comments

Related manuals for 2362387

Brand: Parker Research Corp Pages: 3

Brand: S.I.T.A. Pages: 32

Brand: Makita Pages: 10

Brand: Raymarine Pages: 90

Brand: 1010music Pages: 2

Brand: 1010music Pages: 4

Brand: Gainsborough Pages: 2

Brand: Gainsborough Pages: 2

Brand: Gait up Pages: 12

Brand: Gait up Pages: 6

Brand: Gaiam Pages: 2

Brand: Garelick Pages: 4

Brand: Qlight Pages: 3

Brand: qtran Pages: 2

Brand: Q-Optics Pages: 2

Brand: Zodiac Pages: 2

Brand: Zipper Mowers Pages: 37

Brand: Zimmer Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands