background image

Package Contents

Products Model #

Important: Please Read Before Installation

INSTALLATION INSTRUCTIONS

A. (1) Fixture Body

!

w w w . v o l t l i g h t i n g . c o m

[email protected] • 813.978.3700

Important Safety Instructions

!

- 2 -

- 3 -

VOLT

®

 Floodlight with Motion Sensor

VFL-40XX-MS-ABZ

Product Dimensions

This luminaire is intended for installation in accordance with local codes 

and the National Electric Code (NEC). Failure to adhere to these codes and 

instructions may result in serious injury, property damage and void the 

warranty.

These instructions do not intend to cover all variations in installation, 

operation maintenance or mounting situations.

1.  Make sure that the power is turned OFF before installing or servicing this 

fixture. 

2.  Warning: this fixture is not intended to be installed within 10 feet [3 

meters] of a pool, spa or fountain.

3.  This fixture is intended to be used only with a power supply 

(transformer) rated maximum of 300 watts (25 AMPS) at 12 volts.

4.  Underground Low Energy Cable must not be buried over 6”  (15.2 cm) in 

order to connect to the main low voltage cable. 

5.  Wiring connections must be made with wire connectors that is suitable 

for outdoor use.

6.  Position the wire connector so that it is located within 6 inches (15.2 cm) 

from a building structure, a luminaire, or fitting.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS

Lighted lamp is HOT!

WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

1.  Lamp gets HOT quickly! Contact only switch/plug when turning on.
2.  Do not touch the hot lens, guard or enclosure.
3.  Keep lamp away from materials that may burn.
4.  Do not touch lamp at any time. Use a soft cloth. Oil from skin may 

damage lamp.

5.  Do not operate the luminaire fitting with a missing or damaged shield.

SAVE THESE INSTRUCTIONS

Model

Input 

Voltage

Power 

Factor

Watt

Input 

Current

Finish

Mounting

7W Flood Light 

AC 12V

>0.65

7W

0.7A

Bronze 

Powder 

Coat

Yoke

10W Flood Light 

AC 12V

>0.65

10W

1A

Bronze 

Powder 

Coat

Yoke

30W Flood Light 

AC 12V

>0.8

30W

3A

Bronze 

Powder 

Coat

Yoke

4.25”

3.45”

6”

3.5”

4.25”

4.5”

2.15”

2.55”

7W Flood Light

2.85”

R0.15”

Ø0.85”

Summary of Contents for VFL-40 MS-ABZ Series








Reviews: