manualshive.com logo in svg

VOKERA Syntesi e, Installation & Servicing Instructions Manual

Share
Download
VOKERA Syntesi e Installation & Servicing Instructions Manual Download Page 51

Supplied By www.heating spares.co  Tel. 0161 620 6677

49

SECTION 10  LPG INSTRUCTIONS

10.3

CONVERTING THE APPLIANCE GAS TYPE
To convert the appliance to another gas type it is
necessary to change the burner injectors and
adjust the gas pressures. It is also necessary to
ensure the jumper tag at JP8 is enabled or
disabled according to the gas type used.

●

To change the injectors see 6.15

●

For correct jumper tag configuration see 7.8

10.4

GAS SUPPLY
The gas supply must be connected to the
appliance by a competent LPG installer and must
be of sufficient size to supply the appliance at its
maximum output.
An existing supply must be checked to ensure
that it is of adequate size to deal with the
maximum rated input of this and any other
appliances that it serves.

10.5

GAS SUPPLY INSTALLATION
The entire installation including the meter must
be purged and checked for gas soundness.

10.6

CHECKING AND ADJUSTING BURNER PRES-
SURE (see fig. 16)
Isolate the appliance from the electrical supply
and attach a suitable manometer to the gas valve
outlet test point.

10.6.1 SETTING THE MAXIMUM BURNER PRES-

SURE (see fig. 44)
Light the boiler as described in 5.7, fully open a
DHW outlet (preferably the bath) and ensure the

HW temperature selector is set at maximum.
Allow the appliance to stabilise.
Compare the reading on the manometer with the
value described in 10.2. If adjustment is required,
remove the protective cap from the gas valve
modulating coil assembly and turn the outer
(10mm) nut clockwise to increase, or counter-
clockwise to decrease the burner pressure.

10.6.2 SETTING THE MIMIMUM BURNER PRESSURE

(see fig. 45)
Once the maximum burner pressure has been
checked and/or adjusted, remove one of the grey
wires from the modulating coil. Compare the
reading on the manometer with the value
described in 10.2. If adjustment is required, turn
the inner (red) crosshead screw clockwise to
increase, or counter-clockwise to decrease the
burner pressure, whilst ensuring that the outer
(10mm) nut does not move. When checking and/
or adjustment has been completed, isolate the
appliance from the electrical supply, close the
DHW outlet, replace the protective cap, refit the
grey wire to the modulating coil, remove the
manometer, and tighten the outlet test point.

IMPORTANT, A GAS SOUNDNESS CHECK
MUST BE CARRIED OUT.

10.1 RELATED DOCUMENTS

  BS 6798

INSTALLATION OF BOILERS OF RATED NOT EXCEEDING 60kW

  BS 5449

PART 1

FORCED CIRCULATION OF HOT WATER SYSTEMS

  BS 5546

INSTALLATION OF GAS HOT WATER SUPPLIES FOR DOMESTIC PURPOSES

  BS 5440

PART 1

FLUES

  BS 5482

PART 1

DOMESTIC BUTANE & PROPANE GAS BURNERS IN PERMAMENT DWELLINGS

10.2

Gas Pressures

25

29

35

Inlet pressure (G31)

37 mbar

Burner pressure maximum

35.5 mbar

35.5 mbar

35.4 mbar

Burner pressure minimum

6.1 mbar

4.5 mbar

3.4 mbar

Maximum gas rate

1.94kg/h

2.25 kg/h

2.72 kg/h

Minimum gas rate

0.77 kg/h

0.77 kg/h

0.77 kg/h

Injector size (quantity)

12 x 0.75 mm

14 x 0.75 mm

16 x 0.77 mm

Flue details (concentric)

Max horizontal flue length (60/100mm)

5.75m

3.75m

0.75m

Max vertical flue length (60/100mm)

6.55m

4.55m

1.55m

Max horizontal flue length (80/125mm)

13.80m

11.80m

6.75m

Max vertical flue length (80/125mm)

15.30m

13.30m

8.25m

Efficiency

SEDBUK (%)

90.7

89.8

90.5

Summary of Contents for Syntesi e





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands