background image

MHG-LR Service Manual 

 

INSTALLING YOUR ICE MACHINE 

5/15/09 

3-19 

 
 
 
 
 
 
 
 
 
Startup Checklist

 

 

!     IMPORTANT     ! 

Be sure to follow the wiring schematic when incorporating overloads. 

This is necessary to provide proper 

protection for the Turbo Refrigerating

 

 machine and its component parts. 

!     IMPORTANT     ! 

 

Installation  Review:    A  Checklist.   

Make  a  visual  check  to  be  sure  these  steps  have  been  taken 

BEFORE continuing. 

 

CHECK: ____ PRIOR TO OPENING VALVES, check all joints for leaks which may have 

developed  during  shipment.    (NOTE:    the  machine  was  shipped  with  a  positive 
pressure of 20-25 PSIG, verify on the freezer pressure gage.) 

 
CHECK: ____ The system is properly evacuated to 500 microns. 

 

CHECK: ____ All refrigerant piping, water supply and drain connections for conformity to 

requirements stipulated in this manual and properly connected to inlets and outlets. 

 

CHECK: ____ Electrical supply for proper size of fuses and for compliance to local and national 

codes.  See the machine nameplate for minimum circuit ampacity and maximum fuse 
size. 

 

CHECK: ____ All field installed equipment (augers, conveyors, cooling towers, bin level controls, 

etc.) for proper installation. 

 
CHECK: ____The applicable portion of the warranty registration/start-up report for proper 

completion. 

 

CHECK: ____ Auger gear reducer oil level oil should run out of side pipe plug when removed. 

 

CHECK: ____ The water distribution at top of freezer to make sure they are in position  

 
 

!     CAUTION     ! 

The compressor crankcase heater should be energized for a minimum of 

four hours and the oil temperature should be 100-110

before attempting to start the compressor. 

!     CAUTION     !

 

Summary of Contents for 12A4171M12





































































































Reviews: