background image

PFW 6875

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

www.vogels.com  |  Europe  +31 (0)40 26 47 400

1) 

Insert a small straw or toothpick into the threaded inserts found on the back 

of the flat-panel.

2) 

Use a pencil to mark the depth of the threaded insert on the small straw or 

toothpick.

3) 

Mark the straw or toothpick 1/8” (3.175 mm) above the depth of the threaded 

insert, as shown in Figure 1.

4) 

Insert the small straw or toothpick into the remaining threaded inserts to 

compare and verify their depth using the straw or toothpick’s 1/8” (3.175 mm) 

allowance mark.

5) 

Locate the correct diameter screw for the threaded insert. 

  If the screw you selected is longer than the 1/8” (3.175 mm) allowance 

mark on the small straw or toothpick, as shown in Figure 2 and Figure 3, 

do not use this screw. The screw length must not bypass the mark.

6)   Test each size of the screws provided.  

         The correct screws should thread easily into themounting point and not pull 

out when tension is applied.

Small Straw or Toothpick

Marking the 1/8” 
Allowance

Small Straw  
or Toothpick

Small Straw  
or Toothpick

Depth Plus 1/8” Allowance
Mark

Depth Plus 1/8” Allowance
Mark

Selecting the Mounting Hardware

Securing the Adapters

Optional adapters are available with your PFW 6875 mount. 
Secure the adapters to the PFW 6875 brackets with the 
supplied M8 washers and Nuts. 

M8 Nylon

 

nut

M8 Washer

Page 7

Summary of Contents for PFW 6875















Reviews: