VM Audio VAS310P Shaker Series Install Manual Download Page 4

Page: 4 / 13

Features Overview

Input Terminal Plate

1/4” TS Jack

Connectors

Speakon Cable

Connectors

Binding

Posts

35 mm

Pole Socket

Bottom

Woofer

Tweeters

Ports

VAS312P

Input

Terminal

Front

Rear

Ports

Speakon Cable Connectors -

Two connectors are

featured which are wired in parallel. Use one connector to

connect to the amplifier and use the second connector to

tap into the signal to drive another loudspeaker.
1/4

” TS Jack Connectors -

Two connectors are featured

which are wired in parallel. Use one connector to connect to

the amplifier and use the second connector to tap into the

signal to drive another loudspeaker.

Binding Posts -

Connector accepts banana plugs, bare

wires, and spade connectors.

Features Overview

Summary of Contents for VAS310P Shaker Series














Search results

Summary of Contents for VAS310P Shaker Series

Reviews:

Related manuals for VAS310P Shaker Series

Brands by name

Popular brands

VM Audio VAS310P Shaker Series, Install Manual

Search results

Summary of Contents for VAS310P Shaker Series

Reviews:

Related manuals for VAS310P Shaker Series

Brands by name

Popular brands