Note.
additional Monitor
Turn on the power supply unit or Commutator BKM.
Note.
Video monitoring initiated from the Monitor
Calls from the doorstation
Note
Activation of the individual doorstation
Calls from the Door Bell button or doorstation BVD
Note
Operation with an additional apartment handset UKP
Note.
intercom priority
Monitor’s
To engage the sleep mode press and hold
until the Monitor LED is off.
Special notes on operation with Commutator BKM-440
main
additional
main
intercom priority
main Monitor’s
main
If the Monitor is connected to the Commutator BKM as an
(see Fig. 7), then individual settings
for the first and second doorstation are not available, the settings will be the same for both doorstations. To perform
settings, make a call to the Monitor from either connected doorstation. Then select a ring tone, set its volume, adjust
brightness, contrast and saturation as described above.
The Monitor’s Power LED (see Fig.1) illuminates with green light.
The Power LED may not illuminate at once, after turning the power on; the delay may take up to 7 seconds. If in
7 seconds the Power LED is still dim, then the Monitor is in the sleep mode (calls are ignored, and all buttons except for
are disabled). To switch the Monitor on, push the
button.
To start video monitoring of door zone in front of the doorstation, push
, or pick up the handset. Image from the doorstation
camera is displayed on the screen
To view door zone in front of the outdoor camera, push the
button.
Where several doorstations are connected to the Monitor through the Commutator BKM, push the
button repeatedly to
view door zone in front of the connected doorstations.
When a call is made from the doorstation, the Monitor is ringing. Image from the doorstation camera is displayed on the
screen.
During intercom, push
to view image from the outdoor camera
(see Fig. 4, 5, 6), if needed. Push
again to switch back to the image from the doorstation camera.
To release the door lock, press
and hold for 1 second (until a beep). The door is unlocked now. After you release the
button, intercom is still available. Hang up the handset. The screen will shut off, and the Monitor will go to stand-by.
You can unlock the door without picking up the handset. When called, just press and hold
until the beep. The door
is unlocked now. After you release
, the Monitor will go to stand-by.
To activate the individual / storey doorstation (i.e. start intercom and video monitoring on your initiative, see Fig. 5), pick
up the handset. Image is displayed on the screen, intercom is available. You can push
to view image from the outdoor
camera, if needed. Push
again to switch back to the image from the doorstation camera.
When the Door Bell button is pushed, the Monitor is ringing and the screen switches on displaying image from the outdoor
camera (see Fig. 4, 5).
Similarly when the call button on the doorstation BVD
is pushed, the Monitor is ringing and the screen is
displaying image from the doorstation camera (see Fig.
If an additional apartment handset is connected to the Monitor, only the Monitor will be ringing, when a call is made
from the Door Bell button or doorstation BVD 403CPO
If an additional apartment handset is connected to the Monitor (see Fig. 4, 5), both the Monitor and apartment handset are
ringing when a call is made to the apartment. The Monitor’s screen is displaying image from the doorstation camera. Pick up
the UKP handset. The ringing will stop, and intercom with the doorstation will be available.
To release the door lock, push the lock release button on the UKP handset After you hang up the handset, the Monitor will
go on stand-by.
The Monitor has
over the additional apartment handset, i.e. when you pick up the
handset during intercom, the additional UKP will be disengaged, and intercom will be set between the Monitor and
doorstation.
,
The Monitor can be connected to BKM-440 either as the
or
device (see Fig. 6, 7). The
Monitor
has
over any additional device, i.e. when you pick up the
handset, the additional Monitor
or apartment handset UKP is disengaged. The additional Monitor cannot activate the individual / storey doorstation.
o view door zone in front of the main entrance doorstation (see Fig. 6), push the button on the
Monitor.
To switch to viewing door zone in front of the individual / storey doorstation, push the button again.
FUNCTIONAL CHECK AND OPERATION ORDER
-403СРО
.
.
,
-403СРО
8).
-
.
.
T
.
Pick up the handset and check duplex intercom.
www.
2016-02)
/1
vizit-group.com VIZIT-M441M Operating Instruction (revision
10 1