Approach MASTER-key No1 or No2 close to the reader. The LED is showing or
corresponding to the MASTER-key used
Press button
on the doorstation keypad A short beep sounds, the LED is showing
To confirm, press MASTER-key No2 has been deleted.
In one second the LED is displaying a blinking cursor The doorstation is on stand-by now
Approach MASTER-key No1 or No2 close to the reader. The LED is showing or
corresponding to the MASTER-key used
Press button on the doorstation keypad A short beep sounds, the LED is showing the first four digits of the password.
In 10 seconds a short beep sounds, the LED is showing the last four digits of the password.
In 10 seconds the LED is displaying a blinking cursor The doorstation is on stand-by now
Approach MASTER-key No1 or No2 close to the reader. The LED is showing or
corresponding to the MASTER-key used
Press button on the doorstation keypad A short beep sounds, the LED is showing the first four digits of the PIN-code.
In 10 seconds a short beep sounds, the LED is showing the last four digits of the PIN-code.
In 10 seconds the LED is displaying a blinking cursor The doorstation is on stand-by now
Press buttons
and simultaneously
Release button first, then button
The LED is showing
Start entering the password within 3 seconds. The interval between entering digits of the password shall not exceed
3 seconds either. If the password is correct, the LED is showing .
In two seconds the LED is displaying Press button
within 10 seconds. A short beep sounds, the LED is
showing The doorstation is ready to key binding.
Approach an RF key close to the reader A short beep sounds, the LED is showing
If this RF key is already bound, the LED is showing
In one second the LED is showing Approach the next RF key close to the reader, and so on.
To quit key binding press The LED is displaying a blinking cursor The doorstation is on stand-by now
Press buttons
and simultaneously
Release button first, then button
The LED is showing
Start entering the password within 3 seconds. The interval between entering digits of the password shall not exceed
3 seconds either. If the password is correct, the LED is showing .
In two seconds the LED is displaying Press button
within 10 seconds A short beep sounds, the LED is
showing .
Enter eight digits of a new password. After the password is entered, a long beep sounds. The password has been
changed. The LED is displaying a blinking cursor The doorstation is on stand-by now
In order to regain access to the doorstation’s settings in case of loss of the both MASTER-keys, do as follows:
Address the manufacturer, furnishing documents that confirm purchase of this doorstation.
Communicate the PIN-code of the doorstation to the manufacturer.
The manufacturer will supply a PUK-code to delete the both MASTER-keys and service personnel password.
The PIN-code of the doorstation will remain unchanged.
To enter the PUK-code, follow the below instructions:
Switch the Control Unit’s power off
Connect
wire to
terminal of the Control Unit see the note on Figure
Switch the Control Unit on. The LED is showing
Enter eight digits of the PIN-code. The LED is showing
Enter eight digits of the PUK-code A long beep sounds, the LED is showing The doorstation is ready for
memorizing
Approach an RF key close to the reader. A short beep sounds, the LED is showing
then another short beep sounds, the LED is showing .
has been memorized.
Switch the Control Unit off, and disconnect PRG wire from GND terminal.
Memorize
and program the service personnel password as described earlier.
7.
.
8.
-
9.
-
1 . RF
7
7
.
7
7
Deleting MASTER-key No2
6
Displaying the service personnel password on the doorstation LED
8
Displaying the PIN-code on the doorstation LED
9
0
key binding with use of the service personnel password
1
11 Changing the service personnel password without the MASTER-key
2
6
MASTER-key No1.
MASTER-key No1
MASTER-key No2
-
,
.
-
.
.
.
.
.
-
,
.
-
.
-
.
.
-
,
.
-
.
-
.
.
-
.
-
.
.
-
-
.
.
-
.
.
.
-
.
-
.
.
.
-
.
-
.
.
-
-
.
.
-
.
.
1.
2.
3.
-
.
-
PRG
GND
(
).
-
.
-
.
-
.
.
-
,
-
-
¬
¬
¬
¬
¬
#
www.
- 43
201 -
/
vizit-group.com BVD 3
F(FCPL) Operating Instruction (revision
5 11) 7 8
