2.
7
7
3.
4.
5.
6.
Memorizing MASTER-key No2
MASTER-key No2
Notes
Changing the PIN-code
2
Changing the service personnel password with use of the MASTER-key
3
Note
11
RF key binding to the doorstation PIN-code with use of the MASTER-key
1
Note.
10
Deleting MASTER-key No1
4
-
(PRG
.
-
.
-
.
.
-
.
,
.
.
-
-
-
,
.
-
.
.
-
.
-
PIN
.
.
.
-
,
.
-
.
.
-
-
.
.
.
.
-
,
.
-
.
.
.
-
.
.
.
-
.
-
.
.
.
:
-
;
-
2;
-
;
-
;
-
;
-
.
-
,
.
-
.
.
.
.
Switch the Control Unit on
wire shall be disconnected from GND terminal of the Control Unit).
The LED is displaying a blinking cursor
Approach MASTER-key No1 close to the reader. The LED is showing
Press button
on the doorstation keypad A short beep sounds, the LED is showing
Approach an RF key close to the reader A short beep sounds, and the LED is showing , then another
short beep sounds, and the LED is displaying a blinking cursor
has been memorized.
The doorstation is on stand-by now
If after application of the RF key the LED keeps displaying , it means that an error occurred during key
memorizing. Approach the RF key close to the reader once more.
If button
is not pressed within 10 seconds after MASTER-key No1 is approached to the reader, the doorstation
will go to stand-by automatically. Approach MASTER-key No1 close to the reader once more.
Approach MASTER-key No1 or No2 close to the reader. The LED is showing or
corresponding to the MASTER-key used
Press button
on the doorstation keypad A short beep sounds, the LED is showing
Enter eight digits of the current PIN-code using the keypad (0000 0000 is the default setting). If the PIN-code is
correct, the LED is showing and a long beep sounds. In one second the LED is showing
Enter eight digits of a new
-code After the code is entered, a long beep sounds. The PIN-code has been changed.
The LED is displaying a blinking cursor The doorstation is on stand-by now
Approach MASTER-key No1 or No2 close to the reader. The LED is showing or
corresponding to the MASTER-key used
Press button
on the doorstation keypad A short beep sounds, the LED is showing
Enter eight digits of the current password using the keypad (0000 0000 is the default setting).
If the password is correct, the LED is showing and a long beep sounds. In one second the LED is
showing .
Enter eight digits of a new password After the password is entered, a long beep sounds. The password has been
changed. The LED is displaying a blinking cursor The doorstation is on stand-by now
The password may be changed without the MASTER-key (see paragraph
).
Approach MASTER-key No1 or No2 close to the reader. The LED is showing or
corresponding to the MASTER-key used
Press button
on the doorstation keypad A short beep sounds, the LED is showing
The doorstation is ready to the key binding procedure
Approach an RF key close to the reader A short beep sounds, the LED is showing
If this RF key is already bound, the LED is showing
In one second the LED is showing Approach the next RF key close to the reader, and so on.
To quit key binding press The LED is displaying a blinking cursor
The doorstation is on stand-by now
Key binding may be done without the MASTER-key (see paragraph
).
The following actions may become necessary during operation of the doorstation
to delete MASTER-key No1
to delete MASTER-key No
to display the service personnel password on the doorstation LED
to display the PIN-code on the doorstation LED
to bind RF keys with use of the service personnel password
to change the service personnel password without the MASTER-key
These actions are performed as described below.
Approach MASTER-key No1 or No2 close to the reader. The LED is showing or
corresponding to the MASTER-key used
Press button
on the doorstation keypad A short beep sounds, the LED is showing
To confirm, press the button. MASTER-key No 1 has been deleted. In one second the LED is displaying
a blinking cursor The doorstation is on stand-by now
¬
#
www.
- 43
201 -
/
vizit-group.com BVD 3
F(FCPL) Operating Instruction (revision
5 11) 6 8
