background image

 
 

5.

 

Praparing for programming & programming mode: 

 

1. After V-LIFT / VMAX-LIFT is installed in furniture, connect the push-button switch to the wire (POTENTIAL FREE 
CONTROL). 
2. Using attached connection scheme, connect V-LIFT / VMAX-LIFT lift, LED diode will flash 20 times. After that system is 
ready to be programmed 

3. Install your LCD TV / monitor on a lift. Programming mode can be run when  V-LIFT / VMAX-LIFT is loaded with your 
display (Symmetrically installed on a V-LIFT / VMAX-LIFT lift). 

   „UP” and „DOWN” position programming: 

1. touch (firm touch) with your finger desired „touch area” (icon) and hold until LED diode flashes 5 times.  Release your 
finger . LED diode will flash 20 times, confirming start programming mode.                                                                                                                                                                                               

2.  

„DOWN” position programming:

 Set your V-LIFT / VMAX-LIFT lift on expected down position, using push-button 

switch, then touch (firm touch) with your finger desired „touch area” (icon) to confirm down position of lift. LED diode will 
flash quickly 4 times confirming this setup. 

3.

  „UP” position programming:

 Set your V-LIFT / VMAX-LIFT lift on expected up position, using push-button 

switch, then touch (firm touch) with your finger desired „touch area” (icon) to confirm up position of lift. LED diode will 
flash 20 times to confirming up  position of lift and closing programming mode.  
 4. 

End of programming:

 V-LIFT / VMAX-LIFT lift is programmed and ready to use.  

 

Attention: After V-LIFT / VMAX-LIFT lif, it is possibile to control it using push-button switch POTENTIAL FREE CONTROL or VOLTAGE 

CONTROL. 

 

6.

 

TECHNICAL DATA: a: V-LIFT; b: VMAX-LIFT 95 

Range of TV models: 

a: 26" do 46"; b: do 95” 

Silent operation: 

42dB 

Height of the mechanism:

 

a: 783mm; b: 856mm 

Max. reach:

 

a: 710mm; b: 1400mm 

Stop positions:

 

Regulationed – programmed 

Mounting location:

 

furnitures, ceiling, wall

 

Power consumption:

 

40 W 

Lift capacity:

 

a: do 70 kg; b: 130kg 

Control:

 

 

RS-232  

 

Switch key 

 

TRIGGER 12V  

 

RF 

 

IR 

Power Supply: 

230 V  /  direct current 

Manufacturer: VIZ-ART Automation 

tel.+48 22/6138899      www.viz-art.eu 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

4/6 

 

Summary of Contents for V-LIFT







Reviews: