Vivotek MD8562 User Manual Download

Page: 5 / 191

VIVOTEK

User's Manual - 5

Hardware Reset

The reset button is used to reset the system or restore the factory default settings. Sometimes

resetting the system can return the camera to normal operation. If the system problems remain

after reset, restore the factory settings and install again.

Reset

: Press and release the recessed reset button with a straightened paper clip. Wait for the

Network Camera to reboot.

Restore

: Press and hold the recessed reset button until the status LED rapidly blinks. Note that

all settings will be restored to factory default. Upon successful restore, the status LED will blink

green and red during normal operation.

Installation

Hardware Installation

First, use the supplied screwdriver to detach the dome cover from the camera base. Insert your MicroSD/

SDHC Card if necessary.

Then, follow the steps below to install the camera to either the ceiling or the wall:

1. Attach the supplied alignment sticker to the ceiling/wall.
2. Using the 3 screw circles on the sticker, drill 3 pilot holes into the ceiling/wall. Then hammer

the plastic anchors into the holes if necessary.

3. This Network Camera can be mounted with the cable routed through the ceiling/wall or from

the side. If you want to feed the cable through the ceiling/wall, drill a cable hole A as shown

in the picture. If the cable goes through the side of the dome cover, please remove the plastic

cover (B).

Record the MAC address

before installing the camera.

Reset Button

Status LED

Dome Cover

Tamper-proof Screw

Camera Base

Plastic Cover

Summary of Contents for MD8562
































































































































































































Search results

Summary of Contents for MD8562

Reviews:

Related manuals for MD8562

Brands by name

Popular brands

Vivotek MD8562, User Manual

Search results

Summary of Contents for MD8562

Reviews:

Related manuals for MD8562

Brands by name

Popular brands