Vivotek MD7530 User Manual Download

Page: 87 / 157

VIVOTEK

User's Manual - 87

Recording

Advanced Mode

This section explains how to configure the recording settings for the Network Camera.

Recording Settings

NOTE

► Before setting up this page, please set up the Network Storage on the Server Settings page first.

► Please remember to format your SD card when using for the first time. Please refer to page 91 for

detailed information�

Network Storage Setting

Click

Server

to open the Server Settings page and follow the steps below to set up:

1� Fill in the information for your server�

For example:

2� Click

Test

to check the setting� The result will be shown in the pop-up window�

Network storage path

(\\server name or IP address\folder name)

User name and password for your server

Insert your SD card and click here to test

Summary of Contents for MD7530






























































































































































Search results

Summary of Contents for MD7530

Reviews:

Related manuals for MD7530

Brands by name

Popular brands

Vivotek MD7530, User Manual

Search results

Summary of Contents for MD7530

Reviews:

Related manuals for MD7530

Brands by name

Popular brands