Vivotek IB8367A User Manual Download Page 73

Page: 73 / 325

VIVOTEK

User's Manual - 73

► If the default ports are already used by other devices connected to the same router, the Network

Camera will select other ports for the Network Camera.

► If UPnP

is not supported by your router, you will see the following message:

Error: Router does not support UPnP port forwarding.

► Steps to enable the UPnP

user interface on your computer:

Note that you must log on to the computer as a system administrator to install the UPnP

components.

1. Go to Start, click

Control Panel

, then click

Add or Remove Programs

2. In the Add or Remove Programs dialog box, click

Add/Remove Windows Components

3. In the Windows Components Wizard dialog box, select

Networking Services

and click

Details

NOTE:

Summary of Contents for IB8367A






































































































































































































































































































































Search results

Summary of Contents for IB8367A

Reviews:

Brands by name

Popular brands

Vivotek IB8367A, User Manual

Search results

Summary of Contents for IB8367A

Reviews:

Brands by name

Popular brands